Access Official Technical PDF

Share Summary:LinkedInEmail

Semiconductor wet bench cleaning is an early but demanding step in producing the high-purity silicon used to manufacture chips. At this stage, polysilicon rods are broken into chunks, then etched, rinsed and dried to remove oxides and other contaminants. For a long production line, the automation challenge is not simply moving baskets between baths: the motion system must coordinate multiple axes, handle heavy loads and meet cleanroom requirements.

JST Manufacturing addressed those demands in a 138-foot cleaning line built for an overseas customer. The system combines overhead Cartesian gantry robots with linear motion and electric drive and control technologies. Its design illustrates how motion architecture, component protection and coordinated integration can shape a specialized wet process system.

Designing a process around throughput and bath sequence

The cleaning station processes polysilicon chunks measuring roughly one to three inches. Operators load the chunks into baskets, each holding about 44 pounds. The line was designed to process approximately four tons during a 22-hour shift, requiring one basket to be cleaned every 6.6 minutes.

To support the process, JST divided the equipment into two units. In the 24-foot A2 section, two-axis robots move baskets along a row of five acid etch baths and two rinse baths. The robots lower each basket into the required bath, then advance it through the sequence.

After the etch and rinse steps, baskets pass automatically through an airlock into the 88-foot A1 section. There, three-axis gantry robots move them through two rows of soak and dry baths. Once processing is complete, customer-supplied conveyor belts unload the empty baskets. This division of tasks connects the chemical process sequence with the movement required to maintain production flow.

Why the long-axis motion system matters

The A1 section presented a substantial travel-distance challenge. JST assembled each side of the X-axis from multiple sections of profiled linear guide rail mounted on extruded aluminum structural framing. At this scale, rail and frame joints had to align precisely to provide smooth robot travel across the length of the line.

Each gantry carriage travels on two synchronized ServoBelt linear motion modules, one on each side. These modules use paired, toothed steel-reinforced polyurethane belts and Rexroth synchronous servo motors. A master-slave configuration synchronizes the drives, helping the carriage travel smoothly along the extended X-axis.

The gantries also use separate motion axes to handle baskets at the baths:

  • X-axis: Moves the gantry carriage along the line.
  • Y-axis: Moves baskets laterally between rows of tanks in the A1 section.
  • Z-axis: Raises and lowers baskets into and out of the baths.

Rexroth CKR belt-driven linear modules provide the A1 gantries’ Y-axis movement. CKK ball screw linear modules provide vertical movement, with a 32-inch stroke in the A1 unit. Each arm ends in a J-hook that engages slots in the basket. The ball screw actuators were selected to provide the smooth, rapid lifting action and robustness needed to move baskets from the baths.

The A2 unit uses the same type of dual ServoBelt modules for X-axis travel, while CKK actuators provide the Z-axis movement. Because its baths are arranged in one row, the A2 system does not require a lateral Y-axis.

Balancing overhead automation with particle control

Overhead Cartesian robots can raise concerns in semiconductor processing because motion components above the product may generate particles. JST evaluated the system under cleanroom conditions and found that the selected profiled guide rails and linear motion modules generated fewer particles than the applicable specifications allowed, according to the company’s account.

Component protection was also important because the system operates around chemical etch baths. Seals help keep the linear motion rolling strips clean and protect modules from chemical exposure that could cause pitting. Thin dense chrome plating provides corrosion resistance, while cleanroom grease is used for lubrication. Together, these design measures supported the stated requirement of Class 10 cleanroom standards or better.

Extending the approach to seed rod cleaning

JST also built a separate system for cleaning seed rods used to grow polysilicon ingots. Cylindrical carriages carry the rods through a sequence of etch baths, with a rotary end-effector turning the rods in the tanks. Rexroth MKR linear modules move the carriages along the X-axis, while a CKK module raises and lowers them into the baths.

For the cleaning stations and seed rod system, the drive, rail and linear motion components were supplied through Rexroth EasyHandling System part numbers. This integrated ordering approach brought the components together as a gantry robot solution and supported the project’s production schedule. JST worked with automation partner Northwest Motion on the projects.

Practical considerations for long-travel cleanroom automation

This application highlights several considerations for engineers and system integrators planning long-travel wet process equipment:

  • Map the process sequence to the axes. Separate X-, Y- and Z-axis requirements clarify how baskets move between rows and baths.
  • Plan rail and frame alignment. Long assemblies depend on accurate joints to support consistent carriage travel.
  • Address contamination and chemical exposure. Seals, corrosion-resistant finishes and suitable lubrication are part of the motion-system design.
  • Coordinate drives across the gantry. Synchronized motion is important when paired modules move a carriage over an extended span.

For semiconductor wet bench cleaning, the practical lesson is that throughput, precision and cleanliness must be considered together. A carefully coordinated combination of linear modules, servo drives and structural components can support complex bath sequences across a long production line. Just as importantly, component selection and integration must account for particle control, chemical exposure and the alignment demands of extended travel.

Access Official Technical PDF

About The Author