Access Official Technical PDF

Share Summary:LinkedInEmail

Low-voltage sources such as photovoltaic panels and fuel cells often need a substantial DC voltage increase before their power can be used by downstream conversion stages. A transformerless voltage quadrupler converter offers one approach: it combines two interleaved boost phases with capacitors and diodes arranged to raise the output voltage while limiting semiconductor voltage stress. For engineers evaluating DC power-conditioning architectures, its main design features are high step-up conversion, reduced device voltage requirements, and automatic current sharing under specified operating conditions.

Why use a high step-up DC-DC converter?

A conventional boost converter can increase voltage, but pushing its duty cycle close to unity creates practical difficulties. The source paper notes that extreme duty ratios can increase conduction losses and voltage spikes, and can worsen diode reverse-recovery issues. These concerns matter in applications where a low-voltage input must feed a much higher-voltage DC bus.

Other high-gain approaches involve trade-offs. Isolated converters can provide voltage gain through a transformer, but may require additional components or measures to manage switch stress and leakage energy. Switched-capacitor designs can achieve large conversion ratios, but may expose switches to high transient currents or require multiple cells. Coupled-inductor designs offer another means of extending gain, though some single-phase arrangements have relatively large input-current ripple.

The proposed topology is nonisolated and transformerless. It is derived from a two-phase interleaved boost converter, then adds two capacitors and two diodes to alter how energy is stored and delivered to the output. The arrangement is described as an input-parallel, output-series configuration: the phases share the input while their energy-transfer paths contribute in series at the output.

How the transformerless voltage quadrupler converter operates

The two switches are driven with interleaved signals separated by 180 degrees. This means the phases do not switch on and off at precisely the same time. During intervals when both switches conduct, the inductors store energy. When one phase’s switch turns off, its diodes conduct and direct energy from that phase’s inductor and the capacitors toward the output. The other phase can continue storing energy during the same interval.

Across a switching cycle, the converter passes through four operating modes. The sequence alternates between both switches conducting and one switch conducting while the other is off. The capacitor and diode network supports the transfer of inductor energy and helps build the elevated output voltage. This interleaved operation is symmetrical between the two phases.

The reported high-gain operating analysis assumes continuous conduction mode (CCM) and a duty cycle greater than 0.5. Those conditions are important: the paper explains that the high step-up behavior and inherent current-sharing characteristic are associated with this operating region. At duty cycles below 0.5, or in discontinuous conduction mode, the converter does not retain the same automatic current-sharing capability; additional phase-current control may then need to be considered.

Lower voltage stress and automatic current sharing

A key design feature is that the switches and diodes do not need to block the full output voltage. In the steady-state analysis, the voltage stress on each active switch is one-fourth of the output voltage, while the maximum diode voltage stress is one-half of the output voltage. Lower device voltage requirements can give designers more flexibility when selecting MOSFETs and diodes. The paper identifies the potential to reduce switching and conduction losses through appropriate device selection, rather than treating lower stress alone as a guaranteed efficiency result.

Current sharing is another useful characteristic. Charge balance in the blocking capacitors enables the two interleaved phases to share input-inductor current uniformly in the specified boosting operating mode, without a separate current-sharing circuit or a complex sharing control method. This can simplify the control and power-stage implementation, provided the converter is operated within the conditions that support this behavior.

Interleaving also means the input current is the sum of the two inductor currents. The prototype results show similar current ripple in simulation and experiment, and the authors report that interleaving reduces input and output ripple compared with a corresponding non-interleaved operation. Actual ripple and component stress depend on the converter design and operating point.

What the prototype results demonstrate

The researchers built a 400 W prototype with a 25 V input and a 400 V output. It operated at 40 kHz with both switch duty ratios set to 0.75. The reported measurements were consistent with the topology’s predicted voltage stresses: switch stress was one-fourth of the output voltage, and the maximum diode stress was one-half of the output voltage.

The paper reports a measured full-load efficiency of 94.32% and a maximum efficiency of 96.05% for the diode-based prototype. It also presents results using synchronous rectification, replacing the four diodes with MOSFETs; for that version, the reported full-load efficiency was 95.67%, with a maximum near 97.12%. These are results for the described prototype, not universal performance figures. The loss analysis identifies active switches, diodes, and input inductors as important contributors, with diode conduction loss notably significant in the original implementation.

Design implications for power-conversion systems

For system integrators and power-electronics designers, the topology is most relevant when a nonisolated stage must provide substantial step-up conversion and lower semiconductor voltage stress is a priority. Its interleaved architecture and capacitor-based current-sharing mechanism may be useful where avoiding additional current-sharing circuitry is desirable. However, the CCM and duty-cycle conditions should be part of the design assessment, particularly if the application must operate across a broad range of input voltage or load.

Component selection, thermal design, ripple requirements, switching strategy, and the choice between diode rectification and synchronous rectification still require application-specific evaluation. The prototype demonstrates feasibility at its stated operating point; it does not by itself establish performance for every power level or operating range.

Conclusion

The transformerless voltage quadrupler converter combines two interleaved boost phases with a capacitor-diode network to achieve high DC step-up gain without relying on an extreme duty cycle. Its principal advantages are reduced switch and diode voltage stress and inherent phase-current sharing in CCM when the duty cycle is above 0.5. Engineers considering the approach should weigh those benefits against its operating-condition requirements and validate efficiency, ripple, and component stresses for the intended system.

Access Official Technical PDF

About The Author