Access Official Technical PDF

Share Summary:LinkedInEmail

Laser direct writing can create conductive patterns on flexible films without processing the entire surface. In a study of a graphene oxide (GO) and copper oxide nanorod (CuO NR) hybrid coating, a focused blue-violet laser converted selected regions into a microstructure containing reduced graphene oxide (rGO) and copper. The approach is relevant to printed electronics because it combines a solution-deposited coating with localized, on-demand pattern formation.

For industrial automation engineers and electronics manufacturers, the work illustrates how laser processing can support functional materials on polymer substrates. It also highlights practical process considerations: the spacing between laser scan lines affected electrical resistance, while excessive irradiation under the narrowest spacing was associated with copper re-oxidation.

How the laser-written hybrid film was made

The researchers prepared the coating from a water-based dispersion of GO and CuO nanorods. They applied this mixture to polyethylene terephthalate (PET) film using a doctor blade, forming a hybrid layer on a flexible polymer substrate. The GO served both as a gel-like binder for the nanorods and as a material that could be transformed into conductive rGO by laser-induced reduction.

A continuous-wave (CW) 405 nm semiconductor laser, operated at 13 mW, was focused through an objective lens and scanned across the coating in air. The computer-controlled stage enabled raster scanning at different line spacings. Rather than treating the whole film, the process acted locally along the scanned paths, creating a patterned area while leaving unirradiated regions between the lines.

This localized approach is distinct from processes that require heating an entire coated substrate. The study describes laser direct writing as a way to limit heat exposure to the polymer by concentrating irradiation in a small area. The reported experiment demonstrates the method on PET; it does not establish a general processing window for other polymers or production conditions.

Laser direct writing changes the film’s chemistry and resistance

Optical microscopy showed that the laser-scanned paths changed from the darker appearance of the original GO/CuO coating to a bright bronze color. Micro-Raman spectroscopy provided evidence of material changes. The characteristic Raman bands associated with CuO were absent on the scanned lines, while signals attributed to rGO were observed. Together, these observations support the formation of an rGO/Cu structure through laser-induced reduction.

The unirradiated gaps also revealed how scan spacing influenced the coating. At wider spacings, CuO Raman bands remained in the gaps. At narrower spacings, those bands disappeared, indicating that the material between scanned lines was also affected under those patterning conditions. At the narrowest tested spacing, 5 μm, a Raman band assigned to Cu2O appeared on the scanned region. The authors attributed this to re-oxidation under excess laser irradiation in air, an important qualification when adjusting scan parameters.

Surface resistivity decreased as scan spacing narrowed. The reported value fell from 200 × 103 Ω/sq for the pattern written at 30 μm spacing to 19.6 Ω/sq at 5 μm spacing. The authors linked the lower resistivity at tighter spacing with changes in the film’s morphology, including more prominent granular structures. These results show that scan spacing is a relevant process variable for balancing pattern coverage and electrical behavior; the 5 μm condition also carried the observed Cu2O-related caveat.

Temperature response points to sensing applications

The rGO/Cu film exhibited a negative temperature coefficient of resistance (TCR): its resistance decreased as temperature increased. For the rGO/Cu-30 sample, the reported TCR was −1.18%/°C, which the study described as more than 50 times the value for graphite. This response suggests potential for sensing applications where resistance changes are used to detect thermal input.

As a demonstration, the researchers fabricated a 5 × 5 mm rGO/Cu sensor and observed a clear resistance response when it was exposed to on-off infrared (IR) illumination. The test used an 850 nm long-pass filter and a stated light power of 102 mW. This is a laboratory demonstration of IR response, rather than evidence of a qualified industrial sensor or of performance under plant operating conditions.

Process implications for printed electronics

The hybrid coating combines two complementary material transformations. Laser irradiation reduces GO to rGO, while the carbon-containing GO composite helps reduce CuO nanorods to copper. In this way, the coating material participates in both film formation and the chemical changes needed to create the conductive microstructure. The reported results show that reduction was achieved with a relatively low-power CW laser in the described setup, without relying on a furnace-based treatment.

For process development, the findings suggest several factors to evaluate before adapting the method:

  • Coating formulation: The demonstrated film used a water-dispersed GO/CuO nanorod mixture applied by doctor blade to PET.
  • Laser pattern parameters: Scan spacing affected surface resistivity and the appearance of the microstructure.
  • Atmosphere and exposure: Irradiation took place in air, and excessive exposure at the narrowest spacing was associated with Cu2O formation.
  • Application requirements: The demonstrated IR response and temperature coefficient indicate sensing potential, but do not by themselves establish suitability for a particular production environment.

Conclusion

Laser direct writing of a GO/CuO nanorod hybrid film offers a demonstrated route to conductive rGO/Cu patterns on flexible PET. The method brings localized patterning and material reduction together, while scan spacing influences resistivity and excessive irradiation may promote copper re-oxidation. For engineers assessing printed-electronics processes, the central practical lesson is to treat coating composition, laser exposure, pattern geometry, and the intended sensing function as linked design variables.

Access Official Technical PDF

About The Author