Access Official Technical PDF

Share Summary:LinkedInEmail

Analog IC design training combines circuit theory with the practical work of simulation, layout and verification. A faculty development program organized by Jawaharlal Nehru Technological University Hyderabad (JNTUH) with Entuple Technologies set out to build these skills through a short, hands-on course. The program, held April 22–24, 2019, offers a useful example of how university–industry collaboration can connect academic instruction with semiconductor design workflows.

The course focused on analog circuit and layout concepts, while also introducing participants to elements of digital ASIC design. Its intended audience included engineering faculty, research scholars, practicing analog design engineers and students preparing for semiconductor careers. Rather than treating circuit design as an isolated classroom topic, the program progressed from basic functional blocks to physical implementation and post-layout analysis.

Why practical analog IC design training matters

The program description highlighted a continuing design challenge: although digital signal processing and digital architectures have advanced, analog components remain a foundational abstraction layer in complex chipsets. It also pointed to increasing pressure to optimize designs for performance, area, energy and cost. Meeting those demands requires engineers who can interpret specifications and make informed choices about circuit topology and implementation.

That combination of skills shaped the course. Participants were expected to work with design requirements, examine device model parameters, build amplifier circuits and understand how layout affects the final design. The emphasis was not only on producing a schematic, but also on checking and characterizing the design through multiple stages.

From CMOS fundamentals to amplifier design

The course began with VLSI fundamentals and CMOS inverter design. Participants examined balanced, symmetric and fastest inverter concepts, then designed and simulated a CMOS inverter using the gpdk180 process design kit (PDK). DC and transient analyses provided a basis for assessing the inverter’s quality metrics.

From there, the curriculum introduced custom IC design flow. The inverter exercise continued into layout capture, design rule checking (DRC), layout-versus-schematic (LVS) verification and parasitic extraction. Participants then considered how extracted resistance and capacitance could be back-annotated for post-layout simulation, with GDSII identified as the layout output.

Later sessions moved into analog amplifier design. Participants worked on a common-source (CS) amplifier with a current-source load, examining both DC and small-signal AC performance. The course also addressed how to interpret design specifications before selecting or developing a suitable circuit topology. This link between requirements and topology is central to designing a circuit that can meet stated performance targets.

Connecting schematic design and physical verification

A schematic-level result does not by itself describe the complete design process covered by the program. Layout introduces physical constraints, and verification checks whether the implementation follows design rules and corresponds to the intended circuit. The course therefore included physical verification, parasitic extraction and post-layout simulation as connected steps.

For a more advanced exercise, the stated learning outcomes included designing and characterizing a seven-pack CMOS compensated operational amplifier at schematic-entry level. Participants were also expected to derive layout constraints, carry out DRC and LVS, perform physical verification and parasitic extraction, and run post-layout simulation and characterization with back-annotation.

The sequence illustrates a practical learning progression:

  • Understand requirements: Translate DC and AC performance specifications into design considerations.
  • Develop and simulate circuits: Work with CMOS inverters and amplifier topologies.
  • Move into layout: Apply physical design constraints to the circuit implementation.
  • Verify and characterize: Use DRC, LVS, extraction and post-layout simulation to examine the design beyond the schematic.

Digital ASIC design in the wider curriculum

Alongside the analog content, the three-day outline included an introduction to digital ASIC design. The front-end topics covered ASIC flow, HDL capture, functional simulation and synthesis. The back-end session addressed physical design of a counter, including floor planning, power planning, placement, clock tree synthesis (CTS), routing and timing analysis, followed by GDSII and post-layout files.

This digital track broadened the course beyond analog design alone. It gave participants exposure to stages from design entry through synthesis and physical implementation, while the analog sessions concentrated on CMOS circuit behavior, amplifier design and layout characterization.

Industry–academia collaboration and skills development

JNTUH established its Directorate of University Industry Interaction Centre (UIIC) in 2009 to support engagement between the university and public, private and government organizations. Its activities include student training, internships, academic projects and placements, as well as training, research and consultancy projects involving faculty. Seminars, workshops and industry visits are also part of its collaborative work.

The analog IC program reflected that broader purpose. Entuple Technologies, a Bengaluru-based technology solutions and research-and-development consulting company, contributed an industry-oriented design environment to the training. The stated objective was to help faculty develop their capability to prepare future engineers, while also serving practicing engineers, research scholars and students.

Practical implications for engineering education

For educators and technical decision-makers, the program’s structure points to the value of teaching design as an end-to-end activity. Learners benefit from seeing how specification interpretation, circuit synthesis, simulation, layout and verification relate to one another. Spreadsheet-based design automation was also included among the intended outcomes, alongside PDK characterization and amplifier design.

The 2019 course is a historical program, not a current registration opportunity. Its curriculum nevertheless shows a clear approach to technical training: combine foundational concepts with guided tool-based exercises, then extend the work into physical verification and post-layout characterization. For universities and industry partners seeking to strengthen semiconductor skills, that connection between academic knowledge and design workflow is the central takeaway.

Access Official Technical PDF

About The Author