GaN X-band MMICs offer a way to address two demanding requirements in transmit/receive (T/R) modules: generating substantial RF output power and protecting sensitive receiver circuitry from high-power signals. A set of designs developed using a 0.25 μm GaN-on-SiC HEMT process demonstrates how power amplifiers, a low-noise amplifier (LNA) and an SPDT switch can support these functions across the X-band.
The circuits were designed as individual monolithic microwave integrated circuits (MMICs), rather than as a completed transceiver on one die. Their results nevertheless illustrate how GaN’s power-handling characteristics can inform a more integrated T/R architecture.
Why use GaN in an X-band T/R module?
Transmitters need output stages that can deliver high RF power in a limited area. Receivers have a different challenge: their front ends must amplify weak signals while tolerating potentially high input power. Traditional architectures may use a limiter ahead of the LNA to protect the receiver. That additional component can complicate integration and, because it sits before the LNA, may affect receiver bandwidth and noise figure.
GaN’s high breakdown voltage and ability to operate at high drain voltages make it suitable for high-power RF circuits. GaN devices and passive structures can also support higher power and voltage swings than the technologies discussed in the design work, including CMOS and GaAs. In a T/R module, those properties can be applied to the PA, receiver LNA and antenna-path switch.
A GaN LNA designed to tolerate elevated input power may reduce the need for a separate limiter, while a high-power switch can route transmit and receive signals. These are potential architectural benefits; the reported work characterizes separate MMICs rather than claiming a completed, fully integrated transceiver.
GaN X-band MMICs: transmit power across two bands
Two power amplifiers were designed to cover adjacent portions of the X-band: 8–10 GHz and 10–12 GHz. Both use class AB biasing, a compromise between efficiency and linearity. The design uses eight output transistors, with combining losses taken into account when sizing the output stage for the target power.
Output matching is critical to extracting power from the transistors. The design process used load-pull simulation to identify suitable load impedances, then implemented matching sections using transmission lines in place of physically large, lower-Q inductors. Electromagnetic simulation was also used to assess the MMIC matching networks and the PCB interconnects.
Thermal management is part of the PA design, not an afterthought. At the reported operating point, the amplifiers had power-added efficiency above 25%, meaning a substantial share of the supplied DC power becomes heat. The assembly therefore used a copper plate and an active cooler. The GaN-on-SiC construction, including source-connected backvias, supports heat removal, but the design still required dedicated cooling.
Continuous-wave measurements showed that both amplifiers produced more than 25 W of output power. The reported measurements were broadly consistent with simulations, with some differences in circuit characteristics.
A receiver LNA designed for gain and input-power tolerance
The three-stage LNA was designed to combine more than 20 dB of gain with a noise figure below 2 dB, while tolerating at least 2 W of RF input power. Its measured operating range was 8–11 GHz, covering the X-band region addressed by the design. The reported comparison gives 22 dB gain and a 1.6 dB noise figure.
Inductive degeneration was used to support low noise and input matching. The input transistor was sized with both noise contribution and power-handling requirements in mind: the first stage is especially important because it contributes strongly to the overall noise figure. Shunt resistive feedback was added at each stage to improve stability.
To assess power tolerance, 2 W was applied at the input and the LNA’s gain and noise figure were checked afterward. Changes in both measures were less than 0.5 dB under the reported test conditions. This is evidence of the device’s tested robustness, not a substitute for evaluating the complete receiver’s operating limits and protection requirements.
SPDT switching for high-power signal paths
The SPDT switch provides a path-selection function between transmit and receive chains. Its design uses shunt transistors and quarter-wave transmission lines rather than relying on a conventional series-shunt arrangement. In the transmit path, the quarter-wave sections and shunt elements help control the voltage swing across the switch transistors, a key consideration for handling high RF power.
Measurements showed insertion loss of about 0.8 dB across the X-band and off-path isolation greater than 50 dB in the band of interest. The switch was also tested with 25 W of continuous-wave RF power. The test setup reached 43.6 dBm, its maximum available output; no change in measured S-parameters was observed at that level. The measured 1 dB compression point at 10.6 GHz was 43.3 dBm.
Practical implications for system designers
Together, these results highlight how GaN can support several demanding functions in an X-band T/R design: high-power transmission, receiver amplification with input-power tolerance, and transmit/receive switching. For engineers and system integrators, the potential value lies not only in the ratings of each block but also in how those blocks could affect module architecture, protection strategies, RF loss and thermal design.
Each application still requires system-level validation. Designers must account for cooling, bias networks, stability, matching, interconnects and the operating conditions of the complete signal chain. The practical takeaway is that GaN X-band MMICs can provide building blocks for compact, high-power T/R modules, while careful integration and thermal planning remain essential to realizing their benefits.