An autonomous solar-powered vehicle is a useful engineering platform for examining how navigation, embedded control and renewable energy work together. A Drexel University senior design project converted a remote-control car into a small autonomous ground vehicle, using GPS coordinates to guide it toward a programmed destination and solar panels to recharge its battery. The prototype also exposed integration challenges familiar to automation teams: sensor accuracy, controller interfaces and the balance between energy generation and consumption.
Although built as an educational project rather than an industrial vehicle, the design offers a practical way to study system architecture. Students had to connect mechanical components, electronics, software and energy storage, then evaluate the complete system through testing.
Autonomous solar-powered vehicle architecture
The team removed the remote-control car’s original control board and installed an Arduino Uno microcontroller with GPS and motor-driver shields. The Arduino became the central controller: it received position data, calculated a route direction and commanded the drive motor and steering servo.
A GPS receiver supplied latitude and longitude as NMEA data. The controller parsed those values and compared the vehicle’s current position with the programmed destination. It calculated distance using the haversine formula and determined the bearing toward the destination. A three-axis magnetometer served as a digital compass, providing the vehicle’s heading relative to magnetic north. Comparing heading with destination bearing enabled the controller to adjust steering.
A servo moved the steering mechanism, using a custom bracket designed in SolidWorks and fabricated with a 3D printer. The drive motor was controlled through a motor-driver shield. This interface matters because the motor draws more current than the microcontroller can handle directly: the Arduino supplies control signals, while the driver handles the motor load.
Navigation performance and integration limits
During testing, the vehicle waited for the GPS receiver to acquire satellite signals before moving. Once it had a position fix, it steered toward the destination and stopped when its coordinates matched the programmed destination coordinates. The prototype demonstrated basic waypoint navigation, but its results depended heavily on GPS performance.
The receiver was reported as accurate to about 10 meters. In a stationary test, repeated position readings varied, with the listed distances from the true position ranging from 3 to 17 meters. The paper also notes that accuracy became slightly worse while the vehicle was moving. Consequently, the prototype was tested between points more than 10 meters apart. A more accurate GPS module was identified as an important improvement for navigating shorter distances.
The compass supplied heading information because GPS did not provide reliable heading updates while the vehicle was turning. Compass calculations also required consideration of local magnetic declination—the difference between magnetic north and true north. This illustrates a broader integration lesson: sensor readings need to be interpreted in the right reference frame before a controller can use them meaningfully.
Communications created another constraint. The Arduino Uno had one serial port, while the system included both GPS and Bluetooth devices. The Bluetooth module was therefore used for a separate manual-control mode, with a different program uploaded before connecting an Android smartphone. The project proposed a controller with multiple serial ports as one way to support more devices. Collision-detection sensors were also suggested as a future addition, but were not part of the demonstrated prototype.
Solar charging and the vehicle power budget
The energy system combined two 2.5-watt solar panels, an MPPT solar charger and a 2,000 mAh lithium-polymer battery. The charger varied its operating voltage to track the panels’ maximum power point, helping extract available electrical power as sunlight and panel temperature change. It also provided the conversion needed between the panels and battery.
Power budgeting helped the team estimate how long the vehicle could operate. Based on the listed total consumption of 1,616.1 mA and the 2,000 mAh battery capacity, the paper calculated a theoretical runtime of about 74 minutes. Actual runtime could be lower when the motor worked harder, such as on rough terrain or in wind.
Testing revealed an important distinction between solar charging and solar-powered operation: the panels could charge the battery, but the vehicle consumed energy faster than the panels replenished it while running. Based on a measured maximum charge current of 250 mA, the calculated minimum time to charge the battery was eight hours. Increasing panel size was proposed as a way to raise charging current, although larger panels would also add weight and could require a larger vehicle.
What the project teaches engineering teams
The prototype’s value lies not only in whether it moves autonomously, but also in how it makes system trade-offs visible. A design team must account for the interfaces among sensors, control hardware, actuators and power components. The project also links mechanical design and fabrication with programming, energy calculations and test results.
- Validate sensor limits: GPS variation affects how close a vehicle can reliably approach a waypoint.
- Check controller interfaces early: Available serial connections can constrain how many devices operate together.
- Size energy components as a system: Battery capacity, motor demand and solar charging rate determine operating and recharge behavior.
- Test under realistic conditions: Terrain and wind can increase motor demand and reduce runtime.
For students, this problem-based approach develops teamwork, communication and project-management skills alongside technical knowledge. For automation practitioners, it reinforces the importance of evaluating integrated-system behavior rather than treating each component in isolation.
Conclusion
The autonomous solar-powered vehicle successfully demonstrated programmed navigation and solar battery charging, while also revealing clear limits in GPS accuracy, serial-device support and charging capacity. Its practical lesson is that autonomy and renewable power must be engineered together: control performance depends on reliable sensing and interfaces, while useful operating time depends on matching energy supply to system demand. These considerations make the prototype a grounded learning tool for robotics, green energy and multidisciplinary engineering design.