Access Official Technical PDF

Share Summary:LinkedInEmail

For a wireless sensor network (WSN) node installed far from routine maintenance, battery capacity can become a limiting factor. Recharging or replacing batteries is difficult in remote or harsh environments, while a single ambient energy source may not be available consistently. A multisource energy harvesting system addresses these constraints by combining solar, wind and thermal inputs with energy storage, helping a sensor node use energy that is available around its deployment site.

A reported field-oriented platform brings these three sources together to power a WSN node without a conventional battery. Its design illustrates an important engineering principle: energy generation, storage and load management need to be considered as one system, rather than as separate components.

Why combine energy sources for a wireless sensor network?

Environmental energy is variable. Solar cells produce power during daylight and are affected by weather and shading. Wind availability changes, while a thermoelectric generator depends on maintaining a temperature difference between its hot and cold sides. Any one source may therefore provide inadequate power at a particular time.

Combining sources can reduce reliance on the availability of any single input. In the described platform, solar, wind and thermal harvesters feed an energy-storage subsystem. The sources can contribute under different conditions, while stored energy buffers fluctuations between periods of generation and periods of sensor operation.

This is particularly relevant for distributed monitoring, where the node may need to collect measurements and communicate them without regular access by maintenance personnel. The power design must account not only for sensor and radio consumption, but also for the energy conversion and storage circuitry.

Multisource energy harvesting: how the platform works

The platform integrates three harvesting modules with a supercapacitor, a control circuit and a wireless sensor node. The harvesters convert ambient energy into electrical output, which is combined and conditioned before being stored. The supercapacitor then supplies the node through an output circuit designed to provide a regulated voltage.

The node’s tested electronics included a CC2530 sensor-node platform and an ADMP401 sound sensor. Power use depended on operating state: the reported maximum was about 56 mW during data transmission, while monitoring in a dormant state required about 20 mW. This difference matters when estimating storage needs and planning communication schedules; average demand depends on how often the node samples, processes and transmits data.

Wind: collecting and directing airflow

The wind harvester uses a vertical-axis turbine inside a wind-collecting structure. Funnel-shaped passages are intended to gather wind from different directions and direct airflow toward the rotor. The design also uses the airflow to help dissipate heat from the thermoelectric generator, linking the wind and thermal subsystems.

In tests, the wind module produced 2.9 mW at a wind speed of 3 m/s and 23 mW at 7 m/s. These results show that its contribution depends strongly on local wind conditions. Wind was not the largest source in the reported measurements, but it can provide useful supplementary energy when solar generation is limited.

Solar: managing output under shading

Flexible solar cells were selected to fit the node’s spherical structure. The designers compared series and parallel arrangements, including tests under shaded conditions. While the connection arrangement had limited effect without shading, series-connected cells lost output more rapidly when shaded. Multiple cells connected in parallel were therefore chosen for the deployment design.

In indoor illumination-simulator tests, the solar subsystem produced up to about 900 mW under sunny-day conditions at roughly 1,000 W/m². At an illumination level of 500 W/m², output was about 235 mW. These are subsystem test results, not a guarantee of output at every installation site; orientation, shade and local weather will affect the energy available.

Thermal: maintaining a temperature difference

A thermoelectric generator converts a temperature difference into electrical energy. Its hot side collects heat, while its cold side must release heat efficiently. If both sides approach the same temperature, the useful temperature difference diminishes and electrical output falls.

To address this, the design paired a solar-absorbing collector plate with a heat-pipe radiator on the cold side. The heat pipe transfers heat toward its radiator, helping the cold side remain cooler than the hot side. The thermoelectric module generated relatively little power in the reported tests—about 3 mW—so it served as a supplemental source rather than the main supply.

Energy storage and power management

Because the three harvesters produce variable outputs, their electrical energy must be managed before it reaches the node. Solar output is direct current, thermal output is low voltage, and the wind generator’s output can be unstable and may be alternating current. The platform connects the harvester outputs in parallel to a step-up module, which supplies a regulated 5.5 V to charge the supercapacitor.

The supercapacitor stores surplus energy and provides a buffer when generation falls. Since its output voltage decreases as it discharges, a separate stage regulates the supply to 3.3 V for the node. The design also uses a diode to limit current flow in the output path. Keeping the management circuit simple was part of the effort to avoid spending too much of the harvested energy on conversion and control.

What the field measurements indicate

Outdoor measurements over nine days recorded an average daily energy generation of 7,805.09 J and average daily consumption of about 2,972.88 J. The reported generation was approximately 6,000 J on a cloudy day and reached about 9,000 J on a sunny day. Across that test period, harvested energy exceeded the node’s measured daily use.

These results demonstrate the potential of the integrated platform under the tested conditions, not a universal guarantee of uninterrupted operation. A deployment assessment should account for site-specific weather, shading, wind availability, node duty cycle, storage capacity and the energy used by power-management electronics. The authors also identify miniaturization as a future challenge: reducing the solar-panel area could reduce solar output and increase the importance of wind and thermal contributions during extended cloudy periods.

Practical implications for automation and monitoring teams

For engineers and system integrators considering remote sensing, the central lesson is to match energy harvesting to the operating environment and the node’s actual load profile. Combining sources can improve resilience to changing conditions, but each harvester, storage component and conversion stage must be evaluated as part of the complete power budget.

A multisource design can reduce dependence on battery replacement for field-deployed WSN nodes when environmental generation and storage are sufficient for the application. The reported platform offers a concrete example: solar supplied the largest measured contribution, while wind and thermal energy added complementary inputs. Site validation remains essential to determine whether that balance can sustain the required sensing and communication schedule over time.

Access Official Technical PDF

About The Author