Access Official Technical PDF

Share Summary:LinkedInEmail

Decoupled PEC water splitting separates hydrogen and oxygen production into physically distinct cells connected electrically. For engineers and system designers, the approach addresses a practical challenge in solar hydrogen systems: collecting hydrogen from many units distributed across a solar field. A benchtop demonstration used hematite photoanodes, silicon photovoltaic modules, and nickel-based auxiliary electrodes to produce hydrogen in a central cell while oxygen evolved at the solar-facing cells.

Why separate the hydrogen and oxygen cells?

In a conventional photoelectrochemical (PEC) cell, hydrogen evolution and oxygen evolution occur in the same sealed assembly, separated by a membrane or diaphragm. That arrangement can support gas separation at small scale, but multiplying sealed cells across a large solar installation creates additional construction and maintenance needs. Hydrogen piping must also connect distributed cells to storage or processing equipment.

A decoupled arrangement changes where the gases are produced. The oxygen cell contains the illuminated photoanode and can release oxygen to the atmosphere; the hydrogen-producing cell is located separately and can be positioned centrally. This removes the need to collect hydrogen gas from every solar-field cell through a manifold. It also avoids a membrane separator in the demonstrated design.

The trade-off is that the system must transfer charge between the two locations. In this demonstration, that function was handled by solid nickel hydroxide/nickel oxyhydroxide auxiliary electrodes. Unlike gas piping, these electrodes have a finite operating capacity and must be exchanged after charging or discharging. The concept therefore shifts part of the system’s operating and logistics challenge from gas handling to electrode management.

How the decoupled PEC water-splitting cycle works

The oxygen and hydrogen cells are linked through an electrical circuit and a reversible redox reaction in the auxiliary electrodes. In the hydrogen cell, the cathode reduces water, producing hydrogen and hydroxide ions. The hydroxide ions are taken up by a nickel hydroxide electrode, which is oxidized to nickel oxyhydroxide.

Electrons travel through the external connection to the auxiliary electrode in the oxygen cell, reducing nickel oxyhydroxide back to nickel hydroxide and releasing hydroxide ions. At the illuminated hematite photoanode, photogenerated holes drive the oxygen evolution reaction. In this way, the auxiliary electrodes mediate hydroxide exchange without a liquid connection between cells.

Because the auxiliary electrodes have limited capacity, they must be swapped before they reach operating limits. A reserve stock can reduce how often the sealed hydrogen cell needs to be opened: electrodes can be exchanged within the oxygen-cell stock during successive cycles, with a larger exchange between the two cell locations only after that stock is used. This makes electrode capacity, cycle duration, and handling procedures important system-design parameters.

Designing the PEC-PV system around operating conditions

The oxygen cell combined two 100 cm2 hematite photoanodes in a back-to-back stack with a silicon PV mini-module. The PV module supplied additional voltage to support unassisted solar water splitting, while the photoanodes absorbed light and drove oxygen evolution. The hydrogen cell used a platinum-coated titanium mesh cathode for the demonstration; the study notes that platinum would need replacement with a more abundant catalyst for large-scale applications.

The photoanode and PV module were electrically connected in series. In a series-connected system, current is constrained by the component with the lower current output, so matching their operating characteristics helps limit coupling losses. The researchers also accounted for reduced light reaching the PV module after it passed through the cell and photoanodes. The oxygen cell used transparent PMMA, while its open design did not require hermetic sealing because hydrogen was not produced there.

Auxiliary-electrode operating limits also required careful selection. Charging too far can promote unwanted oxygen evolution in the hydrogen cell; discharging too far can lead to hydrogen evolution at an electrode in the oxygen cell. The system therefore used two electrodes per operating cycle and selected a partial state-of-charge range rather than fully charging or discharging them. This illustrates a broader engineering principle: component sizing and operating windows must be set together, based on expected current, cycle time, and allowable side reactions.

Demonstrated performance and practical limits

Under simulated sunlight and without external bias, the system completed ten cycles averaging 8.2 hours each, with an average short-circuit current of 55.2 mA. The reported solar-to-hydrogen efficiency was 0.68%. The voltage efficiency relative to an equivalent single-cell system was reported as 95%, with the difference attributed to the voltage gap between charging and discharging auxiliary electrodes.

The system was also operated outdoors under natural sunlight. During the reported eight-hour test, the average current was 31.6 mA under partly cloudy conditions. In a separate configuration, a 25-ohm load connected in parallel enabled simultaneous hydrogen production and electricity generation. The reported overall efficiency was approximately 1.7% (1.76% in the test results).

These results demonstrate a working separate-cell concept, not a finished industrial production system. The design still depends on periodic handling of solid electrodes, and the demonstration used a platinum-containing cathode. The authors identify mechanical electrode swapping as a key technical challenge that may require automation. Further development of photoanode performance and the overall PEC-PV tandem system is also needed.

What the architecture means for scale-up

For plant planners and system integrators, the central design question is whether moving hydrogen production to a central location offsets the logistics of transporting and exchanging auxiliary electrodes. The answer will depend on the solar-field layout, electrode capacity, cycle schedule, and the practical design of collection and swapping operations. Controls and automation would need to coordinate electrode state, operating cycles, and safe separation of the gas-production locations.

Decoupled PEC water splitting offers a distinct system architecture for solar hydrogen: fewer distributed hydrogen connections in exchange for managed solid-state charge-transfer components. The demonstration establishes that separate oxygen and hydrogen cells can operate together under simulated and natural sunlight. Its practical implication is a promising design direction, alongside clear engineering work still required in electrode handling, materials, and scale-up.

Access Official Technical PDF

About The Author