Access Official Technical PDF

Share Summary:LinkedInEmail

In AlGaN deep ultraviolet light-emitting diodes (DUV LEDs), efficiency can fall as drive current rises. This DUV LED efficiency droop is linked in part to electrons escaping the active region instead of recombining there to produce light. A reported 270 nm device study tested a specifically designed superlattice p-type electron blocking layer (p-EBL) to address this loss by improving hole injection while limiting electron leakage.

The result illustrates an important design trade-off: an electron blocking layer must confine electrons in the multiple quantum wells (MQWs), but it can also impede the holes needed for radiative recombination. The superlattice structure was designed to manage both carrier pathways.

Why carrier balance limits DUV LED efficiency

AlGaN DUV LEDs use MQWs as their light-generating active region. Electrons and holes must reach these wells and recombine efficiently for the device to emit light. However, p-type, Al-rich AlGaN can have a low free-hole concentration, making hole transport into the MQWs difficult. When holes are scarce, fewer electrons recombine in the active region, leaving more opportunity for electrons to leak into the p-type layers.

That leakage reduces useful light generation and contributes to efficiency droop as current density increases. A conventional p-EBL helps prevent electrons from escaping, but the barrier can also hinder hole injection. The challenge is therefore not simply to make the electron barrier higher: the layer must also support hole transport.

How the superlattice p-EBL was designed

The researchers compared two LED structures that differed in their p-EBL. One used a 10 nm Al0.60Ga0.40N-based layer. The other used a five-period superlattice made from alternating 1 nm Al0.45Ga0.55N and 1 nm Al0.60Ga0.40N layers.

In the superlattice device, the sequence began with the lower-aluminum-content layer after the final quantum barrier. This placement was intentional. At the interface, polarization-induced negative sheet charges help deplete electron accumulation in the final barrier, supporting electron confinement. The alternating layers also create a structure that, according to the study’s calculations, favors hole transport through the p-EBL.

Both devices used five-period AlGaN MQWs and were grown on an AlN template. Their emission peaked at approximately 270 nm. By keeping the p-EBL as the key structural difference, the comparison focused on how its design affected device behavior.

Measured changes in efficiency and droop

Electroluminescence measurements showed stronger emission from the superlattice device than from the device with the conventional p-EBL. The measured external quantum efficiency (EQE) was approximately 90% higher for the superlattice structure. At a current density of 110 A/cm2, the reported efficiency droop was about 4%, compared with about 24% for the conventional-layer device.

These results are specific to the devices and conditions reported; they do not establish that the same improvement will occur in every DUV LED design. The study also used numerical calculations to examine carrier distributions and energy bands, with calculated trends agreeing with the measurements.

What changes inside the device

More holes reach the active region

At a modeled current density of 50 A/cm2, the average hole concentration in the superlattice p-EBL was reported to be two orders of magnitude higher than in the conventional p-EBL. The calculations also showed a higher hole concentration in the MQWs. A greater supply of holes supports more electron-hole recombination in the light-generating region.

The modeled effective valence-band barrier for holes was lower in the superlattice device: approximately 281 meV, compared with 324 meV for the conventional structure. This change is consistent with easier hole transport across the p-EBL.

Fewer electrons escape the MQWs

The superlattice also altered the energy-band profile near the final quantum barrier. The calculated effective conduction-band barrier for electrons increased from approximately 295 meV in the conventional device to 391 meV in the superlattice device. The higher barrier favors electron confinement and reduces the opportunity for electrons to escape into the p-type injection layers.

Measurements of parasitic emission and modeled electron concentrations in the p-type layers supported the interpretation that the superlattice device had reduced electron leakage. The calculations further showed stronger radiative recombination in its MQWs. Together, improved hole supply and increased electron confinement help explain the higher EQE and lower droop.

Implications for DUV LED design

For engineers developing AlGaN DUV LEDs, the findings underline why p-EBL design must balance electron blocking with hole injection. A layer that confines electrons but creates a substantial hole barrier may leave the active region short of the carriers needed for efficient radiative recombination. In this design, the superlattice and its interface sequence were used to influence both barriers.

The work is also a reminder that evaluating an LED at a single operating point can miss important behavior. The reported comparison considered emission, EQE, current-dependent droop and modeled carrier profiles. For device development, these measures help connect a structural change to its effect on carrier transport and light generation.

Conclusion

A specifically arranged AlGaN superlattice p-EBL improved hole transport into the MQWs while helping suppress electron leakage in the reported 270 nm DUV LEDs. The measured device showed higher EQE and substantially lower efficiency droop than its conventional p-EBL comparison. The practical design lesson is to treat carrier confinement and hole injection as linked requirements when engineering electron blocking layers for deep ultraviolet emitters.

Access Official Technical PDF

About The Author