Access Official Technical PDF

Share Summary:LinkedInEmail

Reliable retention of configuration and other small data sets is an important part of many embedded control designs. The N24C256 I2C EEPROM provides 256 Kb of nonvolatile memory in a compact six-ball WLCSP package, with a two-wire interface that can operate at Standard, Fast or Fast-Plus I2C speeds. For automation engineers and system integrators, its practical characteristics include not only capacity and bus rate, but also page-write behavior, hardware write protection, power-up handling and package requirements.

N24C256 I2C EEPROM capacity and interface

The device stores 256 Kb, organized as 32,768 eight-bit words—equivalent to 32,768 bytes. The memory is divided into 512 pages of 64 bytes. A two-byte memory address selects a location, while the I2C slave address includes the device address input, A2, and a read/write bit.

The N24C256 supports I2C clock rates of 100 kHz (Standard), 400 kHz (Fast) and 1 MHz (Fast-Plus). It operates from a 1.7 V to 5.5 V supply across an industrial temperature range of −40°C to +85°C. The data sheet specifies separate read and write operating conditions: read operation is listed from 1.6 V to 5.5 V across the temperature range, while write operation from 1.6 V is specified from 0°C to +85°C. Engineers should use the applicable operating conditions when checking a design’s supply and temperature requirements.

The serial interface uses SCL for the master-generated clock and SDA for bidirectional data. Both bus lines connect to the supply through pull-up resistors. The device includes Schmitt triggers and noise suppression filters on the SCL and SDA inputs; system-level bus design must still account for the selected clock rate, bus capacitance and signal rise times.

Page writes and write-cycle behavior

A write begins when the master sends a START condition, the slave address, a two-byte memory address and the data. After the master issues a STOP condition, the EEPROM starts its internal write cycle. During this interval, which is specified as up to 5 ms, the device does not acknowledge read or write requests. A controller can use acknowledge polling after the STOP condition to determine when the EEPROM is ready for another operation.

For a single-byte update, the master sends one data byte. For larger transfers, page write mode can load up to 64 bytes in one write cycle. The device increments its internal byte address as data is received. A key implementation detail is that the address counter wraps within the selected page: sending more than 64 bytes in one page-write sequence overwrites earlier bytes in that page. Firmware should therefore split writes at page boundaries and ensure each transfer stays within the intended page.

The stated endurance is 1,000,000 program/erase cycles, and the data sheet specifies 100-year data retention under its stated conditions. These figures describe device characteristics, not a substitute for assessing how often an application updates particular memory locations or validating the part under the design’s actual operating conditions.

Read access, addressing and protection

The N24C256 supports immediate, selective and sequential reads. An immediate read returns data from the current internal address. A selective read first sets the address counter using the two address bytes, then reads from that location. During sequential reading, the master acknowledges each byte it wants to continue receiving; the counter advances through subsequent locations and wraps at the end of the memory array. To finish, the master sends a NoACK followed by STOP.

The A2 input allows two N24C256 devices to share an I2C bus. When A2 is low, the device uses the 0xA0 write and 0xA1 read address values; when high, the values are 0xA8 and 0xA9. If A2 is left floating, the input defaults to zero. Confirm the address convention used by the controller and firmware when configuring the bus.

Write protection is controlled by WP. Connecting WP to the supply protects the entire memory array from writes, making the device read-only. When WP is grounded or left floating, normal write operations are permitted. This pin can provide a hardware-level safeguard where the design requires protection against unintended changes.

Power-up, package and integration considerations

Power-on reset circuitry places the device in standby after VCC rises above the reset trigger level and returns it to reset if supply voltage falls below that level. This bidirectional behavior is intended to help protect against incorrect power-up states and brown-out events. The specified delay from stable VCC to readiness is 0.35 ms, so a controller should allow for the device’s startup interval before issuing commands.

The six-ball WLCSP package is ultra-thin, measuring 1.09 × 0.96 × 0.19 mm with 0.35 mm pitch. Its small footprint may suit space-constrained boards, but the board layout and assembly process must match the package requirements. The data sheet specifically cautions that WLCSP EEPROM devices must never be exposed to ultraviolet light, because exposure can cause stored data loss.

Before release, review the I2C timing limits for the chosen speed, pull-up and bus loading, page-boundary handling in firmware, write-cycle polling, WP configuration and supply behavior. Also verify that package assembly and handling practices protect the stored contents.

Conclusion

The N24C256 combines 32 KB of nonvolatile storage with three I2C speed modes, 64-byte page writes, selectable addressing and hardware write protection. Its integration is straightforward when firmware respects page wraparound and write-cycle timing, while electrical design observes the applicable operating conditions. For WLCSP implementations, careful assembly and avoidance of ultraviolet exposure are essential considerations. Together, these details help engineering teams assess whether the device fits the data-retention and interface needs of an industrial control design.

Access Official Technical PDF

About The Author