Access Official Technical PDF

Share Summary:LinkedInEmail

Electromigration can gradually damage metal interconnects as high-density current moves atoms within the conductor. For engineers assessing electronic hardware reliability, a rising resistance or a final open circuit reveals that a problem has developed—but may not show where damage began or how it evolved. Electromigration imaging using thermoreflectance offers another view: it maps temperature changes across a device, helping expose localized hot spots associated with non-uniform current flow.

A study of asymmetric aluminum test lines illustrates why that spatial information matters. The researchers observed different failure locations under opposite voltage polarities, even though the physical structure remained the same. The results point to a practical lesson for interconnect design and reliability evaluation: overall electrical measurements alone may not capture the local conditions that determine where a failure occurs.

Why electromigration creates localized reliability risks

As electrons move through a metal conductor, collisions transfer momentum to metal atoms. At sufficiently high current density, this electron-wind force can drive atomic movement. Over time, material may accumulate in some regions and leave others, producing features such as hillocks and voids. A large void can interrupt a conductor, while material accumulation can contribute to an unwanted short circuit.

These processes are influenced by the conductor’s geometry and operating conditions. Narrow sections and abrupt transitions can crowd current into smaller areas. That concentration can increase local Joule heating, while changes to the metal’s structure can further alter the current distribution. The result is a feedback-prone local environment that a single resistance reading may not describe in detail.

Conventional electromigration testing often tracks overall resistance or the voltage at failure. Those measures are useful, but they do not directly reveal the location or progression of hot spots. Spatial temperature measurements can help fill that gap by showing where heating is concentrated as electrical stress increases.

How thermoreflectance imaging maps hot spots

Thermoreflectance imaging (TRI) uses changes in a material’s reflectance as an indicator of temperature change. In the reported experiment, electrical pulses heated the aluminum line, and an imaging system recorded reflected light during heated and lower-temperature portions of the pulse cycle. Comparing those images produced a spatial map of temperature change across the device.

The test structure was an aluminum line with an intentionally created void next to a material reservoir. The reservoir and void were designed to balance the average material volume per unit length with the connected ordinary line. This arrangement made it possible to examine whether nearby material could help address void-related damage. The researchers also tested the structure with opposite voltage polarities.

TRI does not directly image moving atoms. Rather, it reveals temperature patterns that can be associated with current concentration and evolving structural damage. In this study, imaging was combined with electrical measurements and post-failure microscopy, allowing the temperature observations to be considered alongside resistance changes and the eventual break location.

Electromigration imaging reveals polarity-dependent failure

With forward polarity, hot spots developed near both the artificial void and the contact-pad junction. As current increased, heating near the void grew, and features consistent with microvoid formation were observed. In the reported trial, however, the interconnect ultimately broke where the narrow line met the larger contact pad. The researchers suggested that the reservoir may have helped preserve the region around the artificial void in this polarity, but the pad failure meant its effect could not be quantified fully.

Under reverse polarity, the failure location shifted. A hot spot developed near the void, and the line broke in that region at a lower current density than in the forward-polarity test. The study reported a current density of approximately 19 × 106 A/cm2 at failure for reverse polarity, compared with approximately 21 × 106 A/cm2 reached in the forward-polarity test. These values describe the tested structures and conditions; they should not be treated as general operating limits for other interconnects.

In both cases, the hottest location did not necessarily coincide with the eventual break. The observations therefore caution against using peak temperature alone as a predictor of failure. Geometry, local temperature gradients, current distribution and electromigration-related structural changes can all affect which region becomes vulnerable.

What the results mean for reliability evaluation

The study highlights several considerations for engineers and technical decision-makers evaluating small metal interconnects:

  • Assess local behavior, not just overall resistance. A device-level measurement can show degradation without identifying where it is developing.
  • Include geometry and polarity in testing. Asymmetric features may behave differently when current direction is reversed.
  • Pay attention to transitions. The junction between a narrow line and a wider pad can be a location of current crowding and heating.
  • Interpret temperature maps alongside other evidence. Imaging, electrical data and post-test inspection offer complementary information about failure evolution.

The findings concern a specific aluminum test structure and do not establish a universal benefit for reservoirs. In the tested configuration, their potential to mitigate void-related failure depended on polarity, and additional work was identified as necessary to evaluate other reservoir designs.

Conclusion

Thermoreflectance-based electromigration imaging provides a way to observe where heating develops as an interconnect is electrically stressed. In asymmetric aluminum lines, opposite polarities produced different hot-spot patterns and failure locations, demonstrating that current direction and local geometry can influence reliability. For engineers, the practical implication is to combine spatial diagnostics with electrical testing when investigating interconnect degradation—and to avoid assuming that overall resistance or the hottest point alone tells the full failure story.

Access Official Technical PDF

About The Author