An electronic key system can help manage access to PC-based control and visualization systems without relying on passwords alone. In an industrial installation, a USB-connected read/write station identifies a coded key and exchanges data with an application through a virtual COM port. Integrators must also understand the system’s limits: access authorization is not the same as safety-rated operating-mode selection.
How an electronic key system supports access control
The system consists of an electronic key and an adapter that reads and writes the key’s data through a non-contact inductive interface. The key contains a transponder with no battery. When the key is placed in the adapter, the reader supplies power and exchanges data without electrical contacts.
In a machine-control environment, keys can be assigned to support access control and monitoring on a PC-based system or part of a control system. The application determines how the freely programmable key memory is assigned and used. This makes the system an identification and access-management element within a larger architecture, rather than a self-contained machine-control solution.
The key’s memory includes 116 bytes of programmable EEPROM, organized in four-byte blocks, plus an eight-byte read-only serial number. Write operations must use four-byte-aligned start addresses and write a multiple of four bytes. Read operations can address memory byte by byte. The serial number can be read separately and is permanently written during key production.
USB connectivity and virtual COM port communication
The adapter connects to a Windows-based PC over USB. The USB connection supplies power as well as data, and the device appears to application software as a virtual serial COM port. The communication approach is therefore similar to using a serial-interface device, even though the physical connection is USB.
After the appropriate driver is installed, the COM port is visible in Windows Device Manager. The application sends read or write commands through that port and receives a response from the reader. The interface uses the 3964R transfer protocol, which wraps messages in control characters and uses acknowledgments and a block check character to help detect transfer errors. When an error occurs, the protocol allows retries before the process is abandoned.
Consistent port assignment matters during commissioning and maintenance. The device should be connected to the same USB port to preserve its Windows COM-port allocation. Moving it or connecting it through a USB hub may require a new allocation, which requires administrator rights. The selected COM port must also match the port configured in the application or protocol driver.
Reading keys, writing data, and interpreting status
Both read and write operations begin with a command from the PC or control system. The electronic-key system then returns either the requested data or a status response. For a write operation, the key must remain in the adapter’s operating range until the reply has been received. Removing it too early can interrupt the intended transaction.
For reliable application behavior, software should check the response rather than assume that a command succeeded. A status response can indicate, for example, that no key is present in the operating distance. Applications should handle unsuccessful reads and writes in a defined way, including informing the operator or preventing an incomplete access-control transaction from being treated as valid.
The adapter’s two-color LED provides a local indication of its state. Green indicates that the unit is ready, while yellow indicates that a functional electronic key has been detected. The LED can help with setup and troubleshooting, but it does not replace application-level validation of key data or command results.
What the EKS FSA switching contacts do—and do not do
The EKS FSA version, available in the G01 housing, adds semiconductor switching contacts. These contacts are off when no key is present or when the key cannot be read. Separate processing evaluates the channels, and the contacts are electrically isolated from the device electronics and from each other.
These outputs can be incorporated into an appropriate safety-related design only with a suitable downstream safety evaluation. The switching contacts alone do not generate a safe signal. The documented arrangement requires dual-channel evaluation using switching contact channel LA together with the data line as channel LB; use of the second switching contact is optional in the described configuration. Engineers must design and validate the complete safety-related system in line with the requirements applicable to the machine and its intended use.
A key presence or access-right result must not be used directly to select an operating mode when that selection is safety-relevant. The electronic-key adapter is not a safety component under the Machinery Directive and must not be relied on as a standalone safety function. Where failure or malfunction could put people at risk, additional suitable precautions and safety-rated devices are required.
Practical integration considerations
Successful deployment depends on more than connecting a USB cable. Before commissioning, system designers and plant teams should confirm that:
- The adapter is mounted and connected according to its installation and electrical requirements.
- The USB driver is installed and the application uses the correct virtual COM port.
- Key data allocation, write protection, and application permissions are defined for the intended workflow.
- Software checks command responses and handles communication or key-read errors.
- Any safety-related function has a separate, correctly engineered evaluation path.
Mounting, electrical connection, and safety-related integration should be handled by personnel with the relevant qualifications. The installation must also account for applicable regulations, standards, and electromagnetic compatibility requirements.
Conclusion: treat identification and safety as separate functions
A USB electronic key system can provide a structured means of identifying users or authorizations in PC-based industrial control environments. Its virtual COM port and 3964R communication protocol offer a defined path for applications to read and write key data, while status responses and local indicators support operation and troubleshooting.
The key engineering decision is to define the system’s role clearly. Use it for access control and monitoring, validate its data in the application, and keep safety-related functions within an appropriately designed and evaluated safety architecture. That separation helps integrators and plant teams use electronic-key identification without assigning it capabilities it is not designed to provide.