Access Official Technical PDF

Share Summary:LinkedInEmail

ePMP wireless Ethernet can provide a bridge between network segments where a physical Ethernet cable is impractical or where a wireless connection is needed between sites. Cambium’s ePMP 5 GHz portfolio includes access points and subscriber radios for point-to-multipoint (PMP) and point-to-point (PTP) links. For industrial automation engineers and system integrators, the central planning task is to treat the radio path as part of the network infrastructure: link conditions, spectrum rules, installation practices, and management all affect how it fits into an operational network.

How ePMP wireless Ethernet fits into a network

The ePMP system functions as an Ethernet bridge. It forwards 802.3 Ethernet packets between network segments and filters packets that do not need to cross the wireless link. From the connected network’s perspective, the radio link can serve as a virtual connection between an access point and one or more subscriber modules.

In a PTP arrangement, the link connects two locations. In a PMP arrangement, an access point communicates with subscriber modules, creating a sector-based network. The ePMP portfolio described in the system documentation supports both topologies, with specific device variants intended for different roles. The ePMP 3000 access point is connectorized for use with a separate sector antenna; Force 300 radios are integrated subscriber units, while the Force 300 CSM and ePMP 3000L are also listed in the portfolio.

These products operate in unlicensed 5 GHz bands, subject to the regulations applicable at the installation location. The ePMP 3000 and Force 300 devices support channel bandwidths of 20, 40, and 80 MHz. Published throughput figures in the guide are maximum values under stated conditions, not guaranteed application performance. Actual results depend on factors including link conditions, radio configuration, and the operating environment.

Radio behavior and link planning

Account for the path and channel

Before selecting equipment or mounting locations, assess the wireless path, including line of sight, obstructions, and expected link distance. The product documentation identifies line-of-sight and near-line-of-sight operation, but those descriptions do not remove the need for site-specific link planning. Obstacles and path loss influence the signal available at the receiving radio, and the chosen channel bandwidth and available spectrum are also part of the design.

ePMP uses time division duplexing (TDD), in which transmission and reception take place at different times. Its wireless operation also includes OFDM, adaptive modulation, MIMO, and, on the ePMP 3000 series, MU-MIMO and Smart Beamforming. These mechanisms form part of how the system uses the radio channel. Adaptive modulation is relevant to link planning because the radio’s modulation behavior is among the considerations associated with changing link conditions; engineers should not plan around a single headline data rate without considering the actual path and configuration.

Check regulatory requirements

Unlicensed operation does not mean unrestricted operation. Local rules determine which frequencies, power levels, and operating conditions apply. In bands or countries where radar systems receive protection, the equipment must detect and avoid co-channel radar operation as required. Set the correct country code during commissioning and confirm that the selected frequencies and installation comply with local requirements. The guide also identifies professional radio, IP networking, and grounding knowledge as important for installers.

Installation is part of network reliability

Outdoor radios and their mounting structures must be installed with appropriate grounding and lightning protection. The guide calls for compliance with applicable electrical codes and recommends professional installation where required. Use outdoor-rated cabling for exposed connections, and follow the equipment’s installation guidance for the power supply, Ethernet cabling, and surge suppression. The power supply is the primary disconnect device; power down and unplug equipment before servicing.

Radio-frequency exposure is another installation consideration. Strong RF fields may be present near an active antenna, so maintain the specified separation distances and turn off the radio before performing maintenance in front of the antenna. Work at height and near power lines also requires particular care.

Configuration, security, and ongoing management

ePMP devices are configured and monitored through a web-based management interface. The installation wizard covers system, radio, network, and security parameters. Management traffic uses the same interface as bridged traffic, so network design should account for how the device will be reached and administered. The guide also describes SNMP, Network Time Protocol, software upgrades, and monitoring tools as parts of system management.

Security settings need deliberate attention during commissioning. The equipment ships with default web-management credentials, and the documentation recommends changing them before installation. Operators should configure security parameters according to recognized practices and their operating environment, while retaining responsibility for the security of the deployed system.

For troubleshooting, begin with the basics: verify power and Ethernet indications, then investigate radio connectivity and whether the link achieves the required data rates. A disciplined process helps distinguish a power or cabling issue from a radio-path or configuration problem. Keep software management and access controls within the site’s operational procedures.

Conclusion: design the link as infrastructure

ePMP wireless Ethernet offers a way to bridge industrial and enterprise network segments over outdoor 5 GHz PTP or PMP links. Successful deployment depends on more than selecting a radio: engineers must validate the path, plan around spectrum and regulatory constraints, install grounding and cabling correctly, and establish secure management practices. Treating these tasks as part of the network design helps teams set realistic expectations and operate the wireless connection as a managed component of the wider communications infrastructure.

Access Official Technical PDF

About The Author