Access Official Technical PDF

Share Summary:LinkedInEmail

Stretchable electronics depend on more than flexible materials. Their interconnects must maintain electrical connections as a device conforms to curved surfaces and experiences strain. Free-standing interconnects address this challenge by allowing the connecting structures to bend out of plane rather than remain constrained within an elastomer. The approach is relevant to conformable electronic patches, including systems that integrate sensors or ultrasound transducers, where both mechanical compliance and dense connections may be needed.

For engineers and manufacturing teams, the central issue is how to combine a stretchable substrate with interconnects that remain electrically isolated, mechanically supported and compatible with microfabrication. A process platform developed for stretchable electronics illustrates why release layers, polymer adhesion, structural supports and patterning quality all matter.

Why stretchable electronics need a different interconnect strategy

Conventional flexible circuits can bend, but bending alone does not provide the conformability needed to follow more complex surfaces. A stretchable system must accommodate changes in distance between components. One established strategy connects relatively rigid device regions with patterned conductors shaped as meanders, serpentine lines or horseshoes. These geometries can act like springs, but when embedded in an elastomer, their movement may be restricted. Local stress and interface forces can contribute to deformation or delamination.

The challenge becomes more significant in designs with a high device fill factor. If rigid areas occupy most of a patch, the smaller regions between them must accommodate a larger share of the overall extension. Applications that need many connections between closely spaced components therefore place demanding requirements on the interconnect layout and fabrication process.

How free-standing interconnects accommodate strain

A free-standing interconnect is not embedded throughout its span in the stretchable matrix. This leaves it room to bend out of plane as the surrounding device stretches. In principle, that motion allows the interconnect to behave more like a three-dimensional spring than a flat conductor constrained to move with the substrate.

This is a distinct design choice, not simply a different pattern for a metal trace. The structure must be released from its temporary fabrication support while remaining connected at intended anchor points. For an electrically functional device, conductive material also needs suitable insulation and structural support. In the approach described in the research, polyimide (PI) serves as an insulating and structural polymer around metal interconnects, while polydimethylsiloxane (PDMS) provides a stretchable elastomer layer.

Fabrication depends on release, adhesion and support

Release stack and pattern definition

Producing a free-standing structure involves building the circuit on a temporary carrier and then releasing it. The process platform uses a glass wafer, a polyimide layer and an aluminum release layer. Laser release, a technique known as Electronics on Plastics by Laser Release (EPlaR), separates the processed structure from its glass support. Establishing a suitable release stack is therefore a key process module: it must support fabrication and enable transfer without defeating the intended free-standing geometry.

Patterning the polyimide is another important consideration. The work includes dry etching with an aluminum hard mask and investigates residues associated with polyimide etching. For manufacturing, this highlights a practical point: the quality of the released structure depends not only on its layout, but also on clean, controlled definition of the polymer features.

PI-to-PDMS adhesion and mechanical anchoring

Free-standing spans still need reliable attachment where they meet the surrounding structure. The research examines adhesion between polyimide and PDMS, including surface modification of polyimide and the use of an intermediate butyl rubber layer. It also describes support pillars and mechanical interlocking as elements of the fabrication flow. Together, these topics show that release and stretchability cannot be optimized in isolation: interfaces and anchoring features influence whether the structure remains integrated during handling and deformation.

For process development, engineers should distinguish between areas intended to remain attached and spans intended to move freely. Adhesion is valuable at anchors but may work against the desired motion if it constrains the interconnect along its length. The design and process must therefore define those regions deliberately.

Design implications for high-density circuits

Free-standing geometries are intended to make substantial interconnect movement possible, but they also add fabrication and integration demands. A design must balance:

  • Electrical isolation: adjacent conductors need an insulating structure, particularly as connection density increases.
  • Mechanical support: pillars and anchoring features help define how the released structures connect to the larger patch.
  • Controlled freedom of movement: the interconnect span needs room to deform, while its endpoints remain secured.
  • Process compatibility: release, polymer patterning and material interfaces must work together in a repeatable fabrication sequence.

The work distinguishes between a large-area technology demonstrator and the later challenge of micron-sized interconnects. It also identifies test methodology as important for characterizing small, fully free-standing structures. That distinction matters for development planning: demonstrating a general process concept does not, by itself, establish a production-ready high-density implementation.

Practical implications for automation and device teams

For industrial automation engineers and technical decision-makers evaluating stretchable electronics, the main lesson is to treat the interconnect as a mechanical structure as well as an electrical path. Layout, polymer encapsulation, substrate interaction and release processing are connected design decisions. A team assessing a potential application should establish the required connection density and deformation behavior early, then consider whether embedded, meander-shaped or free-standing structures best fit those requirements.

Process development should also include attention to material interfaces and fabrication residues, rather than focusing only on conductor geometry. Where a device uses rigid components on a compliant substrate, the attachment zones and moving spans have different functional needs and should be designed accordingly.

Conclusion

Free-standing interconnects offer a way to let stretchable circuit connections bend out of plane instead of being fully constrained by an elastomer. Their potential value lies in applications that need conformability alongside closely spaced or numerous connections. Realizing that potential requires coordinated engineering of release layers, polyimide patterning, PI-to-PDMS adhesion, structural supports and mechanical anchors. For device teams, the practical takeaway is clear: stretchability is a system-level fabrication challenge, and interconnect mechanics must be considered from the earliest stages of design.

Access Official Technical PDF

About The Author