Galfenol thin films offer a route to magnetostrictive materials for compact sensors, actuators and other devices where magnetic fields can produce mechanical response. Their performance, however, depends on more than alloy composition. A study of DC-sputtered iron-gallium (FeGa) films shows how substrate temperature can alter film structure, surface morphology, magnetic anisotropy and magnetostriction. Among the temperatures examined, 250°C produced the highest measured effective magnetostriction: 59 ± 2 parts per million (ppm).
The result is useful for engineers and system designers evaluating thin-film magnetostrictive materials: the growth process influences the properties that matter in an application, and raising temperature does not necessarily improve them continuously.
Why substrate temperature matters for Galfenol thin films
Magnetostriction describes a material’s change in shape or dimensions in response to a magnetic field. In a thin-film device, that response is relevant to converting magnetic input into mechanical motion or sensing a change in magnetic conditions. The size and direction of the response are affected by the film’s magnetic behavior, crystal structure and microstructure.
FeGa, also known as Galfenol, has been studied as an alternative to rare-earth-based magnetostrictive materials. The study focused on how changing substrate temperature during deposition affects the resulting film, while keeping other key sputtering conditions consistent. Films were deposited on silicon by DC magnetron sputtering at 50°C, 150°C, 250°C and 350°C. The films were approximately 500 nm thick and received no post-deposition treatment.
This controlled comparison helps connect a manufacturing choice—the substrate temperature during growth—to changes in material characteristics. It does not establish a universal optimum for every deposition system or device design, but it identifies a clear peak within the conditions tested.
Temperature changes film structure and surface morphology
Microscopy showed that the films’ morphology changed as the substrate became hotter. At 50°C, the surface had a relatively uniform, prismatic appearance made up of smaller particles. At 150°C, the prism-like forms became less distinct. By 250°C, particles were more spherical and varied in size. At 350°C, the particles had less defined shapes and a flake-like appearance.
The cross-sectional images also revealed changes in growth. The lower-temperature film contained narrow columns made up of smaller grains. As temperature increased, the columns evolved and became more distinct, before the columnar structure collapsed at 350°C into a more planar, randomly oriented growth pattern. The film grown at this highest temperature also showed increased surface roughness.
X-ray diffraction identified both L12 and B2 FeGa phases, with L12 dominant across the films. The B2 phase became more apparent at higher substrate temperatures. Crystallite size increased from about 20 nm to 35 nm as temperature rose, although the 350°C film showed reduced crystallinity compared with the 250°C film. This illustrates why temperature-related changes cannot be interpreted as a simple, continuous improvement in crystal structure.
Magnetic anisotropy and the 250°C result
Measurements in the plane of the film and perpendicular to it showed magnetic anisotropy: the films behaved differently depending on the measurement direction. The easy axis of magnetization was in the plane of the substrate, and the field needed to reach saturation was lower in-plane than out-of-plane.
Magnetization increased with substrate temperature up to 250°C, reaching 406 emu/cc in-plane and 363 emu/cc out-of-plane. At 350°C, it fell to 110 emu/cc and 100 emu/cc, respectively. The greatest anisotropy was also observed in the 250°C film. These results align with the measured magnetostriction trend:
- 50°C: 46 ± 2 ppm
- 150°C: the study reports an overall range of 42–59 ppm but does not specify a separate value in its text.
- 250°C: 59 ± 2 ppm, the highest measured value
- 350°C: 42 ± 5 ppm
The authors link the 250°C result to the combination of higher magnetization, stronger anisotropy and good crystallinity. They also suggest that a greater fraction of the B2 phase may contribute, since the phases present in FeGa have different magnetostrictive contributions. The L12 phase is associated with negative magnetostriction, while B2 is associated with positive magnetostriction. The observed performance therefore reflects interacting structural and magnetic factors, rather than temperature alone.
Practical implications for thin-film device development
For engineers considering sputtered FeGa in sensors or actuators, the findings highlight the need to treat deposition temperature as a material-design parameter. A higher setpoint may change grain shape, columnar growth, roughness, phase balance and magnetic response at the same time. Those changes can affect whether a film’s properties suit a particular device architecture.
The 250°C condition was the best-performing point in this study, not a guaranteed recipe for other equipment or applications. The work used a specific target composition, deposition power, argon pressure and silicon substrate. Different process conditions may yield different structures and magnetostrictive behavior, so validation under the intended manufacturing process remains important.
Conclusion
Substrate temperature significantly influenced the structure and magnetic properties of these DC-sputtered Galfenol thin films. The 250°C film combined the highest measured magnetization and anisotropy with a maximum effective magnetostriction of 59 ± 2 ppm. At 350°C, the altered morphology and reduced crystallinity coincided with lower magnetization and magnetostriction. For industrial automation applications that depend on reliable magnetostrictive response, the practical lesson is to optimize the full deposition process—not simply increase growth temperature—and assess structural and magnetic properties together.