Access Official Technical PDF

Share Summary:LinkedInEmail

GaN VCSEL lateral optical confinement addresses a key design challenge for blue and violet vertical-cavity surface-emitting lasers: keeping light within a small region of the active area without introducing excessive optical loss. A reported device uses a curved mirror formed directly on a GaN substrate to shape the cavity mode. The results show how mirror geometry can support a longer cavity while retaining lateral confinement, potentially easing the precision demands associated with cavity fabrication.

Why GaN VCSEL cavity design is challenging

GaN-based VCSELs are of interest for applications that include displays, optical communications, sensing and solid-state lighting. Their potential benefits include low threshold current, compact arrays and high-frequency operation. However, practical development has been constrained by mirror fabrication and by the difficulty of confining the optical mode laterally.

Distributed Bragg reflectors (DBRs) are central to the cavity design. Semiconductor DBRs can provide high reflectivity, but some GaN-based material combinations are susceptible to cracking, while AlInN/GaN reflectors can have a narrow high-reflectivity stopband. That narrow band places demanding requirements on layer-growth control so the cavity mode remains within the reflective region. Dielectric DBRs offer a wider stopband, but they do not by themselves solve another problem: balancing cavity length, diffraction loss and longitudinal-mode spacing.

A short cavity can reduce diffraction loss, but it produces widely spaced longitudinal modes. The cavity length must then be controlled closely enough for a mode to overlap the gain spectrum of the InGaN quantum wells. A longer cavity narrows the mode spacing and makes that overlap less sensitive to exact length, but can increase diffraction loss enough to prevent lasing when the mirrors are planar and there is no lateral guiding.

How a monolithic curved mirror confines light

The reported design replaces one plane mirror with a curved mirror formed monolithically on the GaN wafer. In a cavity with curved and plane mirrors, the mirror curvature and cavity length determine the beam waist and lateral mode size. The curved surface focuses the resonant mode toward the plane-mirror side, where the quantum wells are located close to the mirror.

This differs from relying on a stepped or mesa-like lateral structure to guide light. Such structures can introduce scattering loss. The curved-mirror approach instead uses the cavity geometry to create a stable resonator and confine the mode, consistent with classical Gaussian optics. In principle, the mode size can be adjusted through the cavity dimensions and mirror curvature, with theoretical miniaturization extending toward the diffraction limit.

To create the curved surface, resin patterns were heated into droplets and used as sacrificial masks during reactive ion etching of the GaN. A dielectric DBR was then deposited over the resulting lens-shaped surface. Measurements found a root-mean-square surface roughness of 0.2 nm at the lenslet top, and microscopy showed the DBR layers following the curved profile. These observations establish the morphology of the fabricated mirror; they do not, by themselves, determine device performance.

Evidence from optical and electrical tests

Optical pumping tests compared cavities with two plane mirrors against cavities with a plane and a curved mirror. The curved-mirror cavity showed a threshold in optical output and a narrower emission spectrum under pumping. The plane-mirror cavity did not show the same threshold behavior. The curved-mirror device had a cavity length of 49.8 µm, illustrating that laser operation was possible in a relatively long cavity under optical pumping.

Current-injection tests used devices with 6 µm and 8 µm apertures. Under pulsed operation at room temperature, the measured threshold currents were 40 mA and 70 mA, respectively. Their threshold current densities were similar, approximately 140 kA/cm2, despite the aperture-size difference. The current-injection cavity was 28.3 µm long, with a measured longitudinal-mode spacing consistent with that length.

Near-field imaging provided further evidence of lateral confinement. At 1.1 times the threshold current, the observed emission formed a concentrated profile within the 6 µm current aperture. The measured spatial profile was fitted by a Gaussian with a standard deviation of 0.723 µm, close to the value predicted from the device dimensions. The authors also noted weak satellite peaks that may be associated with higher-order lateral modes, indicating that mode behavior warrants further investigation.

Implications for fabrication and device development

The practical significance is the possibility of decoupling two constraints that are difficult to satisfy simultaneously in a planar cavity. Lateral optical confinement can limit diffraction loss, while a longer cavity can provide narrower longitudinal-mode spacing. That combination could reduce the need for extremely precise control of cavity length during processes such as polishing. The curved mirror’s geometry is also defined by patterning and processing steps, rather than being determined solely by a very short polished cavity.

The demonstrated threshold current density remains high, and the study identifies possible substrate absorption as one contributor. The GaN substrate occupies much of the cavity, and estimated absorption could add loss comparable to the expected gain in a typical VCSEL structure. Further work would be needed to assess how cavity length and substrate doping affect thresholds, and to clarify the relationship between lateral modes and the observed spectral features.

Conclusion

A monolithic curved mirror provides a route to lateral optical confinement in GaN VCSELs while allowing cavities longer than those typically favored to control diffraction loss. Near-field profiles, aperture-dependent threshold measurements and emission spectra support the role of the curved mirror in guiding the optical mode. For engineers and device developers, the approach is notable because it may relax cavity-length fabrication requirements, although reducing optical loss and threshold current remains an important development task.

Access Official Technical PDF

About The Author