Access Official Technical PDF

Share Summary:LinkedInEmail

High-speed PCB layout is a signal-integrity challenge as much as a component-placement task. As electronic systems become denser and signals switch faster, trace geometry, reference planes and material properties can influence whether signals arrive at their destinations with acceptable timing and amplitude. A considered layout helps limit crosstalk, reflections, ground bounce and noise generated by the distributed power network.

For automation hardware, these principles matter wherever control, communication or data signals must remain reliable on a compact board. The practical aim is to provide predictable transmission paths, suitable impedance, effective grounding and appropriate termination—not simply to route each connection between pins.

High-speed PCB layout starts with transmission-line behavior

A PCB trace has resistance, inductance and capacitance. At high frequencies, a sufficiently long trace behaves as a transmission line, with a characteristic impedance determined in part by trace width and thickness, dielectric properties, and the distance to a reference plane. In general, a wider trace lowers impedance, while increasing the height above the reference plane raises it.

Two common structures are microstrip and stripline. A microstrip is routed on an outer layer with a reference plane beneath it. A stripline runs on an inner layer between reference planes, which can provide shielding and a more controlled signal environment. The required dielectric spacing differs between these structures, so a stripline board may need a thicker dielectric span to achieve the same impedance as a microstrip.

Impedance should be designed into the stack-up and trace geometry, then checked using appropriate calculation tools. A discontinuity between the trace, source and load can reflect energy along the line. At the receiver, reflections may appear as ringing, overshoot or undershoot and can cause a signal to fluctuate near a logic threshold. Shortening high-frequency routes also reduces the opportunity for unwanted coupling.

Routing practices to reduce crosstalk and distortion

Crosstalk is unwanted electromagnetic coupling between nearby signal paths, especially parallel traces. Spacing, layer selection and the proximity of a reference plane all affect coupling. Where board space permits, increase separation between signals. The application note recommends spacing of at least three times the dielectric height and placing signal traces close to a ground plane; it also gives a center-to-center spacing guideline of at least four times the trace width for adjacent traces.

Routing choices can help avoid long parallel runs and unnecessary discontinuities:

  • Keep signal paths short and as straight as practical. Use smooth, approximately 45-degree or curved bends rather than sharp right-angle turns.
  • Route clock lines perpendicular to key signal lines where they must cross, rather than alongside them.
  • Keep clock routing on one signal layer and avoid vias in clock paths where possible.
  • Use a nearby reference plane; for an inner-layer clock, place the trace between reference planes.
  • Consider differential routing where the interface supports it, and route single-ended signals on different layers at right angles when that helps reduce coupling.

Maintain differential-pair geometry

Differential traces should remain consistently spaced and have equal lengths. The guidance recommends a separation of at least three dielectric heights between the traces, with at least six dielectric heights between adjacent differential pairs. If a pair cannot be length-matched exactly, keep the difference below 5 mils and add compensating length near the mismatched end. Route both conductors with consistent bends and avoid unnecessary vias, which can change impedance.

Control ground bounce through power and return paths

Ground bounce can occur when multiple outputs switch quickly and draw transient current to charge load capacitances. The resulting voltage disturbance is influenced by parasitic inductance in the switching and return paths. Reducing that inductance calls for short, wide connections and a well-planned power distribution network.

Place recommended decoupling capacitors close to the device power and ground pins. Keep connections between capacitor pads and vias short and wide, and connect ground pins or vias individually to the ground plane rather than daisy-chaining them. Low-ESR and low-ESL surface-mount capacitors can help limit lead inductance; multiple capacitance values may be placed in parallel close together where appropriate. Power-pin connections to a plane should also be short and wide.

On multilayer boards, dedicated power and ground planes provide low-resistance distribution and can support short return paths. Separate analog and digital power regions where required, and place each type of component over its corresponding ground region. If power planes are isolated with ferrite beads, follow the intended plane and grounding strategy carefully; the source guidance also calls for a ground-plane margin at the board edge to limit fringing RF radiation.

Choose stack-up, material and vias together

Board build-up depends on package choices, routing density and impedance requirements. Place signal layers next to reference planes to provide return paths. High-speed signals routed on inner layers between planes gain shielding from external emissions, while multiple ground planes can lower reference impedance and reduce common-mode radiation. Keep power and ground planes continuous where the design permits.

Material properties affect propagation speed and loss. If dielectric constant varies with frequency, different frequency components can arrive at different times, distorting a digital signal. Signal loss also increases with frequency, attenuating the harmonics that make up the waveform. FR-4 is widely used and economical below 1 GHz, while the note identifies dedicated high-frequency laminates such as Rogers RO4350 for applications above that range. Material selection should reflect the required frequency, impedance consistency and board construction.

Vias add parasitic inductance and capacitance, creating impedance discontinuities. Minimize unnecessary layer changes, particularly on clock and differential paths. When vias are needed for return currents, place return vias close to signal vias and keep the route tightly coupled. Avoid long via stubs; the guidance recommends keeping stubs below 15 mils. Short, wide connections from decoupling capacitors to their vias also help limit inductance.

Match termination to the signal path

Termination helps reduce reflections by making the source, transmission line and load impedances compatible. Source termination places a series resistor near the driver, while end termination places a pull-up or pull-down resistor near the receiver. The appropriate approach depends on the circuit and signal path, so termination should be considered alongside the controlled-impedance layout rather than added as an afterthought.

The application note cites 50-ohm matching for single-ended routing and 100-ohm matching for differential routing as recommendations. These values should be validated against the interface, component requirements and board design; they are not universal targets for every signal.

Build signal integrity into the design process

Reliable high-speed PCB layout comes from coordinating routing, stack-up, materials, grounding, vias and termination. Engineers and system integrators should establish the signal and impedance requirements early, provide continuous reference paths, limit unnecessary route length and layer changes, and verify the final geometry for the specific application. These practices give plant and equipment designers a sound basis for reducing noise and preserving signal quality in dense electronic hardware.

Access Official Technical PDF

About The Author