Choosing an image sensor for an industrial camera involves more than comparing pixel counts. Resolution, frame rate, exposure control, output interfaces and power requirements all affect how a camera can fit into a machine vision or monitoring system. The IMX462LQR image sensor is a 2.13-megapixel CMOS device designed for surveillance, factory automation (FA) and industrial camera applications. Its combination of Full HD readout, selectable operating modes and multiple output options gives camera designers several parameters to consider when developing an imaging system.
IMX462LQR image sensor: resolution and architecture
The IMX462LQR is a CMOS active-pixel sensor with a Type 1/2.8 image format and a 6.46 mm diagonal. Its square pixels measure 2.9 µm by 2.9 µm. The device contains approximately 2.16 million total pixels, of which approximately 2.13 million are effective pixels. The recommended recording area is 1920 by 1080 pixels, or about 2.07 megapixels.
These figures describe different parts of the sensor array. Total pixels include the full array, while effective pixels are those used for imaging; the recommended recording dimensions specify the output image area. For camera design, that distinction helps avoid treating the sensor’s total pixel count as the delivered frame resolution.
The sensor uses red, green and blue primary-color mosaic filters. The product information describes high sensitivity, low dark current and no smear as characteristics of the device. It also specifies three supply rails: 2.9 V analog, 1.2 V digital and 1.8 V interface. These requirements are relevant when planning a camera’s power architecture and supporting electronics.
Readout modes and frame-rate options
Readout mode determines which image area and resolution a camera obtains from the sensor. The IMX462LQR supports all-pixel scanning, 720p HD readout and window cropping. It can also read out in normal or inverted horizontal and vertical directions. These choices provide configuration options for camera implementations, although the appropriate mode depends on the system’s image-processing and integration requirements.
In Full HD 1080p mode, the specified maximum frame rate is 120 frames per second. The listed 720p mode also supports a maximum of 120 frames per second, with a recommended recording resolution of 1280 by 720 pixels. Both modes are specified with LVDS or CSI-2 output and 10-bit or 12-bit analog-to-digital conversion.
A high frame-rate capability can be useful where a camera must capture rapid changes, but the sensor specification alone does not determine the performance of a complete camera system. Designers also need to account for the selected output interface, data handling and the rest of the imaging chain.
Exposure control and HDR functions
The sensor includes an electronic shutter with variable charge-integration time. Its variable-speed shutter function adjusts exposure in units of 1H. Controlling integration time is an important part of configuring image capture for the lighting and motion conditions the camera is intended to handle.
The IMX462LQR also lists two high dynamic range (HDR) functions: multiple-exposure HDR and digital-overlap HDR. These are distinct sensor functions for HDR operation. The product information identifies their availability but does not provide performance figures or specify how a particular camera should configure them. System designers should therefore assess the required HDR behavior against the complete camera implementation rather than infer image quality from the feature name alone.
Gain, conversion and digital output
For signal conditioning, the device includes correlated double sampling (CDS) and a programmable gain amplifier (PGA). Its listed gain range runs from 0 dB to 29.4 dB in 0.3 dB steps for analog gain. From 29.7 dB to 71.4 dB, the specified range combines 29.4 dB of analog gain with 0.3 dB to 42 dB of digital gain, also in 0.3 dB steps.
The sensor provides a 10-bit or 12-bit analog-to-digital converter (ADC). Its output choices include CMOS parallel output in SDR mode, low-voltage LVDS serial output in DDR mode, and CSI-2 serial data output. LVDS can be switched between 2-, 4- and 8-channel configurations; CSI-2 supports two or four lanes, with RAW10 or RAW12 output.
These interface alternatives affect how the sensor connects to downstream camera electronics. Selection should follow the target system’s interface design and the desired bit depth and lane configuration. The device also includes a timing adjustment circuit, horizontal and vertical drivers, and serial communication circuitry.
Design considerations for industrial camera teams
When evaluating the IMX462LQR for an industrial or automation camera, engineering teams can use the specification to structure their initial review:
- Image format: Confirm that the recommended 1920 × 1080 recording area or 720p mode matches the application’s resolution needs.
- Capture timing: Check whether the available frame rates and variable integration-time control suit the intended imaging conditions.
- Dynamic range approach: Determine whether multiple-exposure or digital-overlap HDR aligns with the camera’s planned operation.
- Data path: Match the parallel, LVDS or CSI-2 option to the camera electronics, including bit depth and channel or lane configuration.
- Electrical integration: Account for the specified analog, digital and interface supply voltages in the camera design.
The product information recommends an exit pupil distance from −30 mm to −∞ and identifies a 110-pin LGA package. These mechanical and optical details should also be checked during camera integration.
Conclusion
The IMX462LQR combines a 2.13-megapixel effective array with Full HD and 720p readout modes, a specified maximum of 120 frames per second, variable exposure control, HDR functions and several output-interface choices. For automation engineers, system integrators and camera designers, the practical value lies in evaluating those features together: resolution, timing, signal processing, electrical requirements and data transport must all suit the intended system. The specification provides a useful basis for that assessment without replacing validation of the complete camera design.