A CMOS image sensor’s resolution is only one factor in determining whether it fits a vision system. Readout modes, data interfaces, power rails, control requirements and the manufacturer’s stated application limits all affect system design. The Sony IMX576-AAKH5-C is a 24.8-megapixel active-pixel sensor with a back-illuminated, stacked structure and Quad Bayer color filter arrangement. Its capabilities are relevant to engineers assessing compact camera hardware, but its specified use is an important part of that assessment.
Inside the Sony IMX576 CMOS image sensor
The IMX576 uses a diagonal 6.475 mm, Type 1/2.78 image area and a square pixel array. Each unit cell measures 0.9 μm by 0.9 μm. The sensor contains approximately 25.85 million total pixels, with approximately 25.20 million effective pixels and 24.83 million active pixels. The active readout area is 5760 pixels horizontally by 4312 vertically.
Its back-illuminated pixel structure is intended to support high sensitivity and low-noise imaging compared with conventional CMOS image sensors, while column-parallel analog-to-digital converters support high-speed capture. The device also integrates analog and digital amplification, image-processing and binning circuitry, timing control, and a CSI-2 serial transmitter. These functions place image acquisition and some supporting processing within the sensor, while the host system remains responsible for configuration and downstream use of the image data.
Quad Bayer readout modes and frame rates
The color filter uses a Quad Bayer Coding arrangement, with red, green and blue filters arranged in a repeating pattern. The sensor offers three stated operating modes, each trading output dimensions or readout approach for a different capture requirement:
- Full-size QBC re-mosaic: 5760 × 4312 pixels at 30 frames per second.
- QBC-HDR: 2880 × 2156 pixels at 30 frames per second.
- 2×2 adjacent pixel binning: 2880 × 2156 pixels at 120 frames per second, in 4:3 format.
These are distinct sensor modes, not interchangeable descriptions of one output. System designers should select the mode against the required image dimensions and frame rate, then confirm that the host processor and data path can accept the resulting stream. The sensor also supports image-area controls, including cropping and scaling functions. The specifications note that horizontal analog cropping is prohibited, so image-window planning should account for that constraint.
Interfaces, clocks and control
Image data leaves the sensor over a MIPI CSI-2 interface using two or four lanes. The stated maximum lane rate is 2.3 Gbps per lane, and the interface is compliant with MIPI D-PHY version 1.2. Output formats include RAW10, RAW8 and COMP8. The selected lane configuration, output format and operating mode should be considered together when designing the receiver and its data-handling path.
For configuration, the IMX576 provides a two-wire serial interface compatible with I2C fast mode at up to 400 kHz and fast-mode Plus at up to 1 MHz. Fast-mode Plus is available only when the input clock is at least 14.5 MHz. The interface accesses control and status registers using 16-bit register addresses and 8-bit data messages.
An external input clock, INCK, operates within a specified range of 6 to 27 MHz. Two PLLs support clock generation for image processing and the output interface; the sensor can operate in single-PLL or dual-PLL mode. Integrators must configure clock parameters for the selected operating conditions rather than treating the PLLs as fixed-frequency outputs.
Power and built-in support functions
The device uses three recommended supply rails: 2.8 V for analog power, 1.05 V for digital power and 1.8 V for the input/output interface, each with a stated tolerance of ±0.1 V. The peripheral circuit guidance includes supply decoupling, but the manufacturer notes that capacitor values and component counts may need review and optimization for each design. Power sequencing, clock setup and register configuration therefore belong in the camera module’s integration plan.
Additional functions include two-dimensional dynamic defect-pixel correction, lens-shading correction and an on-chip temperature sensor. The device also supports dual-sensor synchronization, flash-strobe control, test-pattern output and a 9.0 Kbit user OTP ROM. These features can support camera-system configuration and operation, but the specification does not remove the need to validate the complete optical, electronic and software implementation.
Application limits and design review
A critical qualification is the manufacturer’s application statement: the IMX576-AAKH5-C is designed for cellular phones and tablet PCs. Sony states that it does not guarantee product quality or reliability when the sensor is used in other applications. The document also cautions against use in critical applications where failure could create a risk of death or injury or significant property damage, and calls for consultation with a sales representative when considering such uses.
For industrial automation teams, this makes application suitability a first-order design question—not a conclusion that can be drawn from pixel count, frame rate or interface compatibility. Before considering the device for a machine-vision or other non-listed application, review the current manufacturer documentation and obtain appropriate guidance. Also assess operating temperature limits: the specified operating range is −20°C to +70°C, while guaranteed performance is specified from −20°C to +60°C. Those ranges are not equivalent.
Conclusion
The IMX576 combines a high-resolution active array, multiple Quad Bayer readout modes, MIPI CSI-2 output and integrated image-support functions. Its electrical and interface details provide a useful basis for system-level evaluation, from power design and clocking to host bandwidth and image-window configuration. However, its stated phone-and-tablet design target and lack of a reliability guarantee for other applications must guide any industrial assessment. Confirm the intended use, operating conditions and full integration requirements before selecting it for a camera system.