In-vehicle wireless sensor networks could help address two persistent challenges in vehicle electronics: extensive wiring and the difficulty of connecting sensors in moving or otherwise inaccessible locations. In an energy-harvesting design, sensor nodes draw power from local sources rather than the vehicle battery and communicate wirelessly with other nodes or electronic control units (ECUs). The practical question is whether available energy and wireless links can meet each node’s requirements in different vehicle compartments.
Measurements and energy-harvester models spanning the engine, chassis and passenger compartments offer a location-specific view of feasibility. The results point to different communication choices for line-of-sight and obstructed links, and show why energy availability cannot be treated as uniform across a vehicle.
Why consider in-vehicle wireless sensor networks?
Conventional vehicle sensors typically receive power through wiring and communicate over established networks such as LIN, CAN or FlexRay. As vehicle functions grow, wiring harnesses become more extensive, adding design and manufacturing complexity and contributing to vehicle weight. Wired connections can also be impractical for sensors mounted on moving parts, such as tires.
An energy-harvesting wireless node replaces the wired power connection with a local energy source and the wired network transceiver with a radio. Its functional unit may still include sensing elements, an analog-to-digital converter and a microcontroller. The change, however, puts new constraints on the system: each node must operate within the power it can harvest, while its radio must deliver the required data rate and sufficiently reliable communication.
Designing around limited node power
A feasible node needs to reduce consumption across sensing, processing and communication. The analysis identifies three practical approaches:
- Low-power sensing: Use efficient hardware and, where the application permits, reduce sensing activity when the measured signal changes slowly.
- Low-power radio operation: Select a data rate and transmit power that meet the application’s needs without unnecessary consumption.
- Duty cycling: Put sensors or transceivers into a low-power sleep state when timing requirements allow.
These techniques matter because the target for a low-power IVWSN node is below 10 mW. That level is more attainable for some applications than others. A sensor with relaxed timing can potentially spend much of its operating cycle asleep, while nodes with strict timing or high sensing-rate requirements have less opportunity to duty cycle. Those demanding applications may need to reduce power through sensor and transceiver design instead.
Communication requirements also depend on function. Engine and powertrain sensing can require rates approaching 1 Mbps, while chassis and occupant-safety applications may need up to 100 kbps and body functions up to 10 kbps. Safety-critical signals require greater reliability than non-critical body data, so a link’s suitability cannot be judged by data rate alone.
Wireless communication depends on link conditions
The comparison considered 2.4 GHz, ultra-wideband (UWB) and millimeter-wave (mmWave) radio. The evaluated transceiver examples could support the application data rates across the assessed domains. The more significant differences emerged in link reliability under interference and obstruction, evaluated using worst-case signal-to-interference-and-noise ratio (SINR).
Match the radio to line of sight and obstruction
For short line-of-sight links in the engine compartment, mmWave produced the strongest results. Its propagation characteristics also limit interference from other mmWave sources. For longer line-of-sight links in the chassis and passenger compartments, its greater attenuation means performance is closer to UWB.
UWB performed best on non-line-of-sight links, particularly in the chassis, where many links are obstructed. It is also vulnerable to interference, but narrowband suppression techniques can help preserve SINR, with lower bandwidth as the trade-off. By contrast, 2.4 GHz suffered heavily from interference across the compartments in the analysis. This makes it a less suitable choice where robust communication is essential, despite its usefulness as an energy source.
These findings underline the importance of mapping sensor locations and link paths before selecting a radio. A technology that works well for a short, clear engine-bay connection may not be the strongest option for an obstructed chassis link.
Energy harvesting varies by compartment
The assessment considered radio-frequency (RF), vibration and thermal harvesting. Its estimates combine measurements—such as received RF power, vehicle acceleration and temperature differences—with harvester models and power-processing efficiencies. They indicate potential useful power, not a guarantee that every installed node will receive a steady supply under all operating conditions.
- RF energy: Harvesting from 2.4 GHz signals could provide up to about 1 mW across the assessed compartments. MmWave harvesting could provide up to about 0.1 mW in the engine compartment; the evaluated UWB option did not provide useful power.
- Vibration energy: The estimated useful output varied substantially by location and driving conditions. Mean outputs were 2.58 mW in the engine compartment, 1.13 mW in the chassis and 170 μW in the passenger compartment. Engine vibration also produced a much higher peak than its mean, illustrating the potential value of storing harvested energy.
- Thermal energy: The model estimated about 4 mW in the engine compartment after warm-up and an average of 0.5 mW in the chassis. The passenger compartment’s measured temperature difference was around 2°C, below the approximately 10°C minimum difference required by the considered thermal-harvesting model.
Together, the estimates suggest that vibration and thermal sources can support nodes consuming below 10 mW in the engine compartment and below 5 mW in the chassis. In the passenger compartment, thermal harvesting was not feasible under the measured conditions; RF and vibration sources were assessed as suitable only for nodes below 1 mW.
Implications for system design
The results support a compartment-by-compartment design rather than a single radio or energy-harvesting strategy for the whole vehicle. Engineers and integrators should assess the node’s power budget, data rate, safety criticality, link obstruction and expected operating conditions together. Where harvested power is intermittent, energy storage may help bridge periods of lower input, but the node’s consumption and available source still need to be matched.
Overall, energy-harvesting in-vehicle wireless sensor networks appear feasible for selected applications, provided that designs reflect local conditions. UWB is a strong candidate for obstructed links, mmWave suits short line-of-sight engine links, and 2.4 GHz RF can contribute useful harvested power even though its communication performance suffers under interference. The practical next step is validating these choices with complete low-power nodes, harvesters and transceivers in the intended vehicle locations.