Access Official Technical PDF

Share Summary:LinkedInEmail

Improving InSe thermoelectric performance may depend not only on material selection, but also on controlling a material’s structure. Thermoelectric materials convert temperature differences into electrical power, making them relevant to waste heat recovery. However, their efficiency depends on several interconnected properties, so improving one metric does not automatically improve overall performance. First-principles calculations of monolayer indium selenide (InSe) indicate that uniaxial compression can reshape its electronic bands and improve its predicted thermoelectric figure of merit, particularly for p-type material.

Why thermoelectric performance is difficult to optimize

The dimensionless figure of merit, ZT, is a common measure of thermoelectric material performance. It combines the Seebeck coefficient, electrical conductivity, absolute temperature, and thermal conductivity. In simplified terms, a high Seebeck coefficient and electrical conductivity are beneficial, while thermal conductivity works against a high ZT. The electronic and lattice contributions to thermal conductivity both matter.

These properties are coupled. For example, increasing the concentration of charge carriers can raise electrical conductivity, but it can also reduce the Seebeck coefficient. A material’s suitability also depends on its semiconductor character and the temperature at which it operates. This makes the search for useful thermoelectrics a balancing task rather than a matter of maximizing a single property.

One approach is to tune the material’s electronic structure. Strain can shift the energies of electronic bands, potentially bringing multiple bands close together in energy. This condition, called band convergence, can increase the number of available electronic states near the energy range relevant to transport. Whether that leads to a higher ZT depends on the resulting changes to transport and thermal properties.

What strain changes in monolayer InSe

The calculations considered monolayer β-InSe under uniaxial compression applied along the zigzag direction, with strains ranging from zero to −7%. The study used first-principles methods to calculate electronic structure and semiclassical Boltzmann transport properties. Its reported results are computational predictions, not measurements of a fabricated thermoelectric device.

As compression increases, the calculated band gap grows from 1.51 electronvolts without strain to 1.86 electronvolts at −7%. More important for transport, the conduction bands converge near the M point at approximately −6% strain. The valence bands also move closer together around the Γ point as strain approaches −7%. These changes alter the available electronic states and are associated with improvements in transport properties.

The response depends on the type of charge carrier. Across the modeled strain range, p-type InSe performs substantially better than n-type InSe in terms of predicted ZT. At room temperature, the maximum calculated p-type value is 0.46 at −7% strain along the zigzag direction. For the armchair direction, the maximum is 0.41 at −5%. By comparison, the largest reported n-type values are 0.026 along zigzag and 0.029 along armchair.

Connecting band convergence to transport

The Seebeck coefficient changes relatively little with compression in the calculations. Instead, the more notable strain response in p-type InSe comes from electrical conductivity and the power factor, which is the Seebeck coefficient squared multiplied by electrical conductivity. The p-type power factor increases by nearly a factor of two under strain. The study reports that this increase, together with the modeled thermal conductivity, produces an overall ZT increase of about 30% compared with unstrained InSe.

The maximum p-type ZT occurs near the calculated band changes: conduction-band convergence appears at −6%, while the valence bands begin to merge between −6% and −7%. The continuing increase in p-type conductivity beyond −6% is attributed to the changes in the valence bands, which are especially relevant to hole transport. For n-type InSe, the calculated conductivity and electronic thermal conductivity change only slightly with strain, and its overall predicted performance remains much lower.

Carrier concentration is another important design variable. The calculations identify different concentrations that maximize ZT at different strain levels and in different directions. This means that strain cannot be considered in isolation: any experimental evaluation would need to consider the attainable carrier concentration alongside the strain state and transport direction.

What the results mean for engineering

For engineers and technical decision-makers, the main takeaway is that mechanical control of a two-dimensional material’s band structure may offer a route to tuning thermoelectric behavior. The results point to several factors that would need to be assessed before considering practical integration:

  • Carrier type: The predicted advantage is strongest for p-type InSe; n-type performance is markedly lower in the modeled conditions.
  • Strain and direction: The calculations apply compression along the zigzag direction and report different maxima for zigzag and armchair transport.
  • Carrier concentration: The optimum is not constant across strain conditions, so it must be evaluated with the mechanical design.
  • Thermal conductivity: The predicted ZT depends on thermal transport as well as electrical properties. The study identifies further experimental measurement of lattice thermal conductivity, including under strain, as valuable.

These considerations also highlight the gap between a promising material calculation and an engineered component. The authors note that experimental validation would need to establish achievable strain and carrier-concentration ranges, as well as thermal conductivity and ZT. Producing and handling monolayer InSe for such tests presents practical challenges, and applying controlled uniaxial strain would require an appropriate experimental method.

Conclusion

First-principles calculations suggest that uniaxial compression can improve the thermoelectric performance of monolayer InSe by changing its band structure and transport properties. The strongest predicted result is a room-temperature p-type ZT of 0.46 at −7% strain along the zigzag direction, near calculated conduction- and valence-band convergence. For industrial automation and energy-system teams, the work is a research-stage indication of how strain engineering could inform material selection and device development—not a demonstrated performance claim for a commercial heat-recovery system. Experimental confirmation of strain, doping, and thermal transport behavior remains essential.

Access Official Technical PDF

About The Author