Natural dye-sensitized solar cells offer a way to investigate plant pigments as light-absorbing materials in photovoltaic devices. In a study of purple cabbage and purple carrot extracts, researchers paired the dyes with nanocrystalline anatase titanium dioxide (TiO₂) and compared cells sensitized with each extract and a 1:1 mixture. The combined extract produced the strongest reported results, while the measurements also show how dye absorption and interaction with the semiconductor matter to cell performance.
How a dye-sensitized solar cell works
A dye-sensitized solar cell (DSSC) uses a light-absorbing dye attached to a porous semiconductor electrode. In the cells described here, the semiconductor was a mesoporous film of anatase TiO₂. When the dye absorbs light, it can transfer an excited electron into the semiconductor. The cell also includes a counter electrode and a redox electrolyte, which mediates electron-transfer processes and helps complete the electrical cycle.
Several parts of this structure influence performance. The semiconductor film needs a surface that can hold dye molecules, while the sensitizer must absorb light and attach to the TiO₂. The study focused on anatase, one of the principal crystalline forms of TiO₂, and on anthocyanins, plant pigments associated with red, purple and blue coloration. Functional groups in these pigments, including carbonyl and hydroxyl groups, can interact with titanium sites on the semiconductor surface.
Preparing the vegetable dyes and TiO₂ electrode
The researchers extracted pigments from purple cabbage and purple carrots using ethanol acidified with 0.01% acetic acid. After washing and drying the vegetables, they blended 10 grams of plant material with 100 millilitres of solvent, filtered the mixture and rinsed the remaining solids to collect more pigment. The extracts were concentrated to 50 millilitres and stored away from light. For the combined sensitizer, equal volumes of the two extracts were mixed.
To prepare the TiO₂, the study used controlled hydrolysis of titanium tetrachloride. Ammonium sulfate was added to the titanium chloride solution, followed by ammonium hydroxide until the mixture reached pH 7. The reaction was heated to 70°C for 10 hours with gentle stirring. The resulting powder was separated and washed before being used to form an electrode layer.
A paste of nanocrystalline anatase TiO₂ was applied to conductive glass and sintered at 450°C for two hours. The coated electrodes were then immersed in dye solution for 24 hours to allow pigment adsorption. After washing away dye that had not attached to the film, the researchers assembled the cells with a platinum-coated counter electrode and an iodide-based electrolyte.
What characterization revealed
X-ray diffraction (XRD) identified the TiO₂ as anatase, with prominent diffraction peaks near 25.3°, 37.9° and 48.1°. The authors reported crystallite sizes of approximately 44–48 nanometres from XRD analysis and an average particle size of 44.34 nanometres from scanning electron microscopy (SEM). The SEM images showed roughly spherical, spongy particles with some agglomeration.
Infrared spectroscopy identified bands associated with chemical groups in the vegetable extracts, including signals assigned to carbon-hydrogen, carbonyl and carbon-oxygen-carbon bonding. The researchers interpreted the spectra as consistent with coloring components that include anthocyanins. Ultraviolet-visible measurements showed absorption peaks for the extract solutions at 510 nanometres for purple cabbage, 520 nanometres for purple carrot and 530 nanometres for the mixture. After adsorption onto TiO₂, the reported peaks shifted to 525, 535 and 565 nanometres, respectively. The study attributed this shift to interactions between anthocyanins and titanium ions at the semiconductor surface.
Comparing cell performance
Photovoltaic performance was measured from current-voltage curves under simulated sunlight at 100 mW/cm². The reported results were:
- Purple carrot: short-circuit current density (Jsc) of 1.96 mA/cm², open-circuit voltage (Voc) of 0.585 V, fill factor of 47% and efficiency of 0.538%.
- Purple cabbage: Jsc of 2.08 mA/cm², Voc of 0.66 V, fill factor of 53% and efficiency of 0.75%.
- Combined extract: Jsc of 3.16 mA/cm², Voc of 0.66 V, fill factor of 62% and efficiency of 1.29%.
Among the three tested sensitizers, the equal-volume mixture gave the highest reported conversion efficiency. Its higher short-circuit current density and fill factor contributed to the result, while its open-circuit voltage matched that of the cabbage-sensitized cell. The authors proposed that differences in the type and concentration of adsorbed anthocyanins could help explain the performance variation. The measurements establish the outcome for the cells and preparation conditions used in this study; they do not, by themselves, demonstrate how the results would translate to other device designs or operating conditions.
Practical implications and limitations
For engineers and technical decision-makers evaluating alternative photovoltaic materials, the study illustrates the value of treating the sensitizer and semiconductor as an interacting system. A dye’s absorption spectrum is only one consideration: its ability to attach to the electrode and support charge transfer also matters. The higher result for the combined extract suggests that blending plant-derived pigments can change cell behavior, though the study does not establish a general recipe for other dyes or device configurations.
The work is a laboratory-scale materials investigation rather than an industrial deployment assessment. It reports photovoltaic measurements for cells made with specific extracts, an anatase TiO₂ electrode and an iodide electrolyte. It does not provide evidence about long-term stability, manufacturing scale-up, or performance in operational environments, so those considerations remain outside the reported findings.
Conclusion
The study demonstrates that purple cabbage and purple carrot extracts can serve as sensitizers in anatase TiO₂ dye-sensitized solar cells, with the mixed extract producing the highest measured efficiency of the three tested options. Its findings emphasize the relationship between pigment absorption, dye adsorption and photovoltaic output. For technical teams, the useful takeaway is not a deployment claim but a materials-design principle: evaluating sensitizers alongside the semiconductor surface is essential when comparing DSSC performance.