Access Official Technical PDF

Share Summary:LinkedInEmail

Lead-free hybrid perovskites are being investigated as photovoltaic absorber materials that could reduce reliance on lead while retaining useful light-harvesting properties. For industrial automation and energy-system decision-makers, the research highlights both the promise and the practical hurdles: replacing lead is not a simple materials swap. Composition, crystal structure, film morphology and interfaces with charge-transport layers all affect how a perovskite solar cell performs and holds up over time.

Lead-based hybrid perovskites achieved rapid efficiency gains, but their use raises concerns about lead toxicity and material degradation. Lead-free alternatives span several chemical families, including compounds based on tin(II), germanium(II), bismuth(III) and antimony(III), as well as structures that combine different metal ions. Each family offers a different balance of optical absorption, charge transport, stability and ease of processing.

Why lead-free hybrid perovskites matter

Perovskites are attractive solar absorbers because their composition can be adjusted to tune their bandgap and response to light. In a photovoltaic cell, the absorber converts incoming light into charge carriers, which must then move through the device and be collected at its contacts. The absorber’s energy levels must therefore align with the electron- and hole-transport materials around it.

Lead-based perovskites have demonstrated strong light-to-current conversion, but moisture and light can contribute to degradation, and released lead requires careful handling and recycling. Replacing some or all of the lead with less toxic metals is one route to reducing that environmental burden. However, lead-free compositions often introduce new challenges, particularly oxidation, defects and increased recombination of electrons and holes.

Tin-based perovskites: high potential, difficult stability

Tin-based hybrid perovskites have received substantial attention because their charge-carrier mobility and diffusion lengths can be comparable to those of lead-based materials. Their bandgaps can also extend absorption toward longer wavelengths, a useful feature for capturing a broader portion of the solar spectrum. Solar-cell results vary considerably with composition and cell architecture: the review reports efficiencies ranging from early, low-performing devices to approximately 13% for a CsSnI3-based cell.

The central materials problem is tin oxidation. Tin(II) can oxidize to tin(IV), creating defects and tin vacancies that contribute to unwanted p-type conductivity and non-radiative recombination. These processes can reduce the voltage and overall performance of a solar cell. Researchers have explored several ways to address the issue, including:

  • Adding excess tin halide or tin fluoride to help limit defects associated with oxidation.
  • Using mixed-halide compositions to adjust bandgaps and reduce vacancy-related losses.
  • Applying reducing treatments during film formation to convert tin(IV) back to tin(II).
  • Improving film uniformity through solvent selection, additives and controlled deposition.
  • Protecting or spatially confining the absorber to reduce exposure to oxygen and moisture.

These approaches also illustrate why device engineering matters alongside chemistry. A pinhole-free film, appropriate transport-layer energy levels and effective interfaces can help realize the potential of a given absorber. In some tin-based systems, changing the halide composition shifts both the optical response and energy levels, so an improvement in one property may come with a trade-off in another.

Other lead-free material families

Bismuth- and antimony-based absorbers

Bismuth(III)- and antimony(III)-based hybrid perovskites are notable for their reported chemical and photochemical stability in ambient conditions. Their photovoltaic performance has generally remained more modest than that of leading lead-based devices, but the materials offer useful design possibilities. Reported bismuth-based cells include devices using methylammonium bismuth iodide and cesium-silver-bismuth bromide, while antimony-based compounds have also been tested as absorbers.

These materials can have different crystal structures from the familiar three-dimensional lead perovskites. For example, some bismuth compounds contain linked bismuth–iodide units. That structural difference affects how charges move and how the absorber should be integrated with the rest of the cell. Research on bismuth-based materials also points to potential optoelectronic uses beyond photovoltaics, including light detection.

Germanium and other metal substitutions

Germanium(II) can form perovskite-like compounds with bandgaps that vary with the organic cation and halide. However, germanium-based materials can be vulnerable to oxidation and moisture-related degradation, and reported solar-cell efficiencies remain low. Layered structures using bulkier organic cations have been explored to improve moisture resistance, showing how spatial organization can influence material stability.

Other approaches include partial substitution of lead with metals such as manganese, strontium or calcium. Such substitutions may affect surface passivation, charge-carrier lifetime or thermal stability. They do not automatically eliminate lead, but they demonstrate how carefully selected dopants can alter the absorber’s properties and reduce the amount of lead in a composition.

Film morphology and cell architecture shape outcomes

Perovskite performance depends not only on chemical composition but also on how the material is organized from the nanoscale to the device layer. Grain boundaries, surface defects and non-uniform coverage can create pathways for recombination or interfere with charge extraction. Researchers have therefore studied deposition conditions, nanocrystal shapes, layered structures and growth within porous scaffolds.

Cell architecture also affects results. In a conventional n–i–p design, the perovskite is deposited over an electron-transport layer and covered by a hole-transport layer. An inverted p–i–n design reverses the order of the transport layers. The best configuration depends on the absorber’s energy levels and the quality of its interfaces. Some designs also explore carbon layers that combine electrode and hole-transport functions.

For system designers, these findings reinforce a practical point: absorber selection cannot be separated from deposition, interface engineering, encapsulation and operating environment. A composition that looks promising by its bandgap alone may not deliver a stable device if it forms a poor-quality film or is mismatched with the transport layers.

Practical implications for photovoltaic development

Lead-free perovskite research has advanced beyond a single replacement strategy. Tin compounds offer attractive charge-transport and absorption properties but require strong control of oxidation and defects. Bismuth and antimony compounds show encouraging stability, while their device performance and charge-transport characteristics remain important development areas. Germanium and mixed-metal compositions broaden the design space, but bring their own stability and processing questions.

The most useful evaluation criteria are therefore broader than peak efficiency. Engineers and technical decision-makers should consider the absorber’s bandgap, charge-carrier losses, film uniformity, compatibility with transport layers, exposure to moisture and oxygen, and the stability of the complete device. Continued progress will depend on coordinating materials chemistry with deposition methods and cell architecture.

Lead-free hybrid perovskites offer a credible research pathway toward photovoltaic absorbers with reduced lead content, but no single material has resolved all the trade-offs. The practical implication is to assess each composition as part of an integrated device: its optical and electrical properties matter, but so do manufacturing control, interface quality and long-term stability. Those factors will determine whether promising laboratory materials can advance toward dependable photovoltaic systems.

Access Official Technical PDF

About The Author