Access Official Technical PDF

Share Summary:LinkedInEmail

The LM317L adjustable voltage regulator offers a straightforward way to create a regulated positive supply without stocking a separate fixed-voltage regulator for every output level. This three-terminal linear device provides up to 100 mA over a 1.2 V to 37 V output range, with the output set by two external resistors. For automation engineers and system integrators, it can be useful in low-current control circuits, reference supplies and other applications where a compact adjustable regulator fits the electrical and thermal requirements.

How the LM317L adjustable voltage regulator sets its output

The regulator maintains a nominal 1.25 V reference between its output and adjustment terminals. A resistor between these terminals establishes a current, and a second resistor connected from the adjustment terminal sets the output voltage. Because the reference voltage is held across the first resistor, the resistor network determines the regulated output. The adjustment-pin current contributes a small error term, which the device is designed to minimize and keep relatively constant as line and load conditions change.

This arrangement makes one regulator adaptable to multiple voltage levels. It can simplify parts selection in designs that would otherwise require several fixed-voltage regulators. The LM317L can also be configured for uses beyond voltage regulation, including a precision current regulator by placing a fixed resistor between the adjustment and output terminals. The datasheet also illustrates applications such as programmable outputs, current limiting and electronic shutdown.

Built-in protection and operating limits

The LM317L includes current limiting, thermal overload protection and safe-area protection. Its overload circuitry remains functional if the adjustment terminal is disconnected, and the output is specified as short-circuit protected. These features provide protection within the device’s operating limits; they do not remove the need to check input conditions, load current and heat dissipation in the complete circuit.

The device is rated for a maximum input-to-output differential of 40 V, while its stated output range extends up to 37 V. These are related but distinct limits: the differential is the voltage between the input and output terminals, not simply the input voltage. The datasheet also identifies a 625 mW power-dissipation condition for specified electrical characteristics and states that power dissipation is internally limited. Designers should therefore assess the actual voltage drop and load current, as well as the package’s thermal conditions, rather than treating the 100 mA output rating as available under every input and output combination.

The regulator also requires a minimum load current to maintain regulation. The datasheet lists a minimum load-current requirement that varies with the input-to-output differential. If the connected load draws too little current, the output may rise above its intended value. This matters in lightly loaded circuits and designs that enter standby or shutdown states.

Capacitor selection and ripple rejection

The LM317L can operate without an output capacitor, but external capacitors may be needed to address wiring distance, ripple or transient response. If the regulator is more than 6 inches from the main input filter capacitor, the datasheet recommends input bypassing. It identifies a 0.1 µF disc or 1 µF solid tantalum capacitor as suitable options for this purpose.

An optional capacitor from the adjustment terminal to ground can improve ripple rejection. The datasheet reports up to 80 dB of ripple rejection with a 10 µF adjustment bypass capacitor under its stated test conditions. When using this capacitor, designers may need protection diodes to prevent it from discharging through internal low-current paths during input or output short circuits. The need for protection depends on the circuit conditions and capacitor values.

Although no output capacitor is required for basic stability, certain capacitance values can cause excessive ringing. The datasheet identifies values from 500 pF to 5,000 pF as a range where this may occur. It describes a 1 µF solid tantalum capacitor, or 25 µF aluminum electrolytic, as a way to suppress the effect. Capacitor type and high-frequency behavior should be considered alongside nominal capacitance.

Layout details that affect regulation

Good load regulation depends not only on the regulator itself, but also on where the resistor network connects. The resistor between the output and adjustment terminals should connect directly to the regulator output rather than at a distant load. Otherwise, voltage drops in the output wiring can affect the regulator’s reference-setting network and worsen regulation.

Where appropriate, returning the lower resistor connection near the load ground can provide remote ground sensing. The source also notes that separate output leads can help reduce resistance between the TO-92 package and the set resistor. These details are especially relevant when wiring resistance is significant relative to the circuit’s regulation requirements.

Choosing the package and application

The LM317L is available in TO-92, SO-8 and 6-bump micro SMD packages. Package selection affects board layout and thermal behavior. The datasheet lists different junction-to-ambient thermal resistance values for these packages, so a design’s power dissipation must be evaluated with the chosen package and assembly conditions in mind. It also cautions that bright sunlight can temporarily affect the reference voltage of the micro SMD version; the output recovers after the light source is removed.

Typical applications in the datasheet include adjustable regulators, current limiters, battery chargers, logic supplies with electronic shutdown and higher-voltage regulator circuits. For higher-voltage designs, the floating regulator arrangement can regulate supplies whose overall voltage is high, provided the input-to-output differential limit is respected and the supporting circuit is designed accordingly. The datasheet notes that full output current is not available at high input-to-output voltages.

Practical design takeaway

The LM317L is a versatile option for low-current adjustable regulation, but successful use depends on more than selecting two resistors. Confirm the input-to-output differential, account for minimum load current and power dissipation, and choose capacitors based on wiring distance and transient or ripple requirements. Careful placement of the setting resistors and attention to package thermal limits help the regulator deliver its intended performance in the finished circuit.

Access Official Technical PDF

About The Author