Access Official Technical PDF

Share Summary:LinkedInEmail

The LM3409HV evaluation board provides a practical platform for examining a PFET-controller buck current regulator designed for high-power LED strings. Its example operating point drives 12 LEDs at a nominal 42 V output and up to 1.5 A average LED current from a 48 V DC input. For engineers assessing LED driver behavior or adapting a reference circuit, the board brings together current regulation, dimming options and alternative load connections in one evaluation design.

LM3409HV evaluation board operating point

The board is built around the LM3409HV, a controller for buck LED current regulation. Its stated input range is 6 V to 75 V, while the example LED string operates at 42 V. The switching frequency is targeted at 400 kHz at the nominal operating point, but it varies across the operating range; it should not be treated as a fixed frequency under every condition.

The relationship between input voltage and LED string voltage matters when assessing operation. If the input falls below the regulated LED string voltage, the converter enters dropout. In that condition, the output voltage ideally follows the input voltage. The board’s published 6 V to 75 V input range therefore describes the range it can accept, not a guarantee that it can regulate a 42 V LED string at every voltage in that range.

The PCB uses four layers, 2 oz. copper and FR4 dielectrics. Those construction details define the evaluation hardware and provide context when reviewing the board layout or considering a modified design.

Current regulation and controller features

The LM3409HV supports a differential, high-side current-sense arrangement and cycle-by-cycle current limiting. The controller does not require control-loop compensation, according to the listed device features. It also includes a 2 Ω, 1 A peak MOSFET gate drive, low-power shutdown and thermal shutdown protection.

These functions are relevant when evaluating the controller as part of an LED power stage: current sensing and limiting relate directly to regulation, while shutdown features are part of the device’s listed protection and operating behavior. The evaluation board is intended to demonstrate the LM3409HV’s features, rather than establish that a particular implementation will suit every LED load or system requirement.

Three ways to evaluate LED dimming

The board supports multiple dimming approaches, allowing engineers to examine how the control method fits a lighting application:

  • Analog dimming: The IADJ pin is used to adjust LED current. The device feature list specifies a 250:1 analog dimming range.
  • Internal PWM dimming: The EN pin is used for PWM dimming, with a listed range of 10,000:1.
  • External shunt PWM dimming: High-frequency external parallel-FET shunt PWM dimming can also be evaluated.

A header designated J1 has a removable jumper that selects the PWM dimming method. When testing, confirm the jumper arrangement and the chosen control method against the board documentation. The listed dimming ranges describe device features; actual behavior in a setup depends on the circuit configuration and operating conditions.

Connecting the LED load

The evaluation board provides two ways to connect an LED load. A right-angle connector, J2, can mate with an external LED load board. This arrangement allows the LEDs to be mounted close to the driver, which the board documentation identifies as a way to reduce potential ringing when no output capacitor is used.

Alternatively, the LED+ and LED− turrets can be used to connect the load. The choice of connection affects how the load is physically arranged relative to the driver, so the connector option is particularly relevant when evaluating the board without an output capacitor. Follow the applicable board documentation when setting up the load and reviewing any observed waveform behavior.

Adapting the reference design

The board can be modified to demonstrate other operating points. The LM3409/LM3409HV datasheet’s Design Procedure is the stated resource for designing around a different set of specifications. In practice, begin by defining the required input and LED-string conditions, then use that procedure to assess the component choices and circuit configuration for the intended operating point.

The kit information lists the LM3409HV evaluation board, the LM3409 datasheet and application notes 1953 and 1954. The LM3409HV datasheet covers the PFET buck controller for high-power LED drives, while the application notes provide board-related documentation. These materials should be consulted before changing the reference circuit or interpreting its setup.

Practical implications for evaluation

The LM3409HV evaluation board is a focused tool for examining a high-side current-sensed buck LED driver, its dimming options and its load connections. Its example 42 V, 1.5 A operating point, 6 V to 75 V input range and dropout behavior provide important context for bench evaluation. Engineers adapting the design should distinguish the board’s accepted input range from the conditions required to regulate a particular LED string, account for switching-frequency variation, and use the datasheet design procedure for alternate specifications. These steps help keep testing aligned with the actual electrical requirements of the application.

Access Official Technical PDF

About The Author