Access Official Technical PDF

Share Summary:LinkedInEmail

The LM7001 PLL frequency synthesizer is an integrated circuit intended to simplify electronic tuning in AM/FM tuner designs. The LM7001J and LM7001JM combine frequency division, reference selection, serial control, and charge-pump outputs in one device. For engineers integrating the part into a tuner, successful operation depends not only on programming the desired divisor, but also on supplying a stable crystal oscillator, selecting the correct input path, and managing noise around sensitive PLL circuitry.

What the LM7001 brings to tuner design

The LM7001J and LM7001JM are NMOS PLL synthesizer LSIs. They are software compatible with the LM7000, but do not include an intermediate-frequency (IF) calculation circuit. The device supports an FM VCO input through a high-speed programmable divider and provides separate signal inputs for FM and AM local oscillators.

Both versions share the same core functions and differ in package: the LM7001J is supplied in a DIP16 package, while the LM7001JM uses an MFP20 package. Selection therefore involves the required package and board implementation rather than a different stated synthesis function.

The IC also provides three band-data outputs, a 400 kHz controller clock output, and an 8 Hz time-base output. BO1 can serve as the time-base output when configured accordingly. These functions allow the device to supply control and timing signals alongside its frequency-synthesis role.

Setting the divisor and reference frequency

Frequency programming uses a divisor value and a selected reference frequency. The device offers seven reference frequencies: 1, 5, 9, 10, 25, 50, and 100 kHz. Reference selection is controlled by serial data bits R0 through R2. The required divisor depends on the target local-oscillator frequency and the chosen reference frequency.

For example, the datasheet illustrates FM operation with a 100 kHz reference. A 100.7 MHz FM VCO frequency divided by 100 kHz gives a divisor of 1007, or 3EF in hexadecimal. Its AM example uses a 10 kHz reference: a 1450 kHz AM VCO frequency divided by 10 kHz gives a divisor of 145, or 91 in hexadecimal.

These examples show why the programmed frequency is the VCO or local-oscillator frequency, not simply the received RF frequency. The example values account for the stated IF when calculating the required oscillator frequency. In an implementation, engineers should derive the divisor from the intended tuner frequency plan and verify that the selected input and reference settings match it.

Serial control and oscillator startup

Configuration data enters through the CE, CL, and DATA pins. Data is acquired on the rising edge of CL. The divisor uses bits D0 through D13 for FM; AM uses D4 through D13. The T0 and T1 test bits should both be set to zero. Other serial fields select band data, the time-base function, the reference frequency, and the divider input.

Serial transfers must not begin until the crystal oscillator is operating normally. The oscillator uses a crystal connected between XIN and XOUT, with a stated operating range of 5.0 to 8.0 MHz and 7.2 MHz as the typical value. Timing requirements for the serial interface vary with crystal frequency; at 7.2 MHz, the listed minimum setup and hold intervals and clock high and low times are 1.5 microseconds. The datasheet gives longer minimum intervals for other crystal frequencies, so firmware timing should be checked against the actual oscillator used.

The crystal circuit constants depend on the selected crystal and printed circuit board layout. The datasheet provides example component values for several crystal types, but recommends consulting the crystal manufacturer about the oscillator circuit. This is an important design step rather than a detail to assume from an example schematic.

Input ranges, supplies, and board layout

The LM7001 has separate FMIN and AMIN signal inputs. With the specified control setting, FMIN supports the stated FM input ranges of 45 to 130 MHz for selected reference frequencies, or 5 to 30 MHz for other reference frequencies. AMIN supports 0.5 to 10 MHz under its specified control condition. These are local-oscillator signal inputs, and the listed input conditions specify a sine wave coupled through a capacitor. Check the applicable range and control bit before connecting a signal source.

The PLL circuit requires power at both VDD1 and VDD2. VDD1 is the PLL supply, while VDD2 supplies the crystal oscillator and time base. Supplying VDD2 alone does not preserve internal data. The specified operating supply ranges are 4.5 to 6.5 V for VDD1 and 3.5 to 6.5 V for VDD2.

PCB implementation has a direct role in keeping unwanted noise away from the frequency-control circuitry. The datasheet recommends:

  • Place a bypass capacitor between VDD and VSS close to the supply pins.
  • Keep the coupling capacitors for FMIN and AMIN close to their respective input pins.
  • Keep the high-impedance PD1 and PD2 connections, including the low-pass filter paths, short and surround that area with a ground pattern.

The charge-pump outputs connect to the external loop-filter path. Because the PD pins are high impedance, long traces or poor grounding can make the area more susceptible to noise. The VCO is designed to continue oscillating even when its control voltage reaches 0 V, avoiding a condition in which a stopped VCO could leave the PLL deadlocked.

Power-up behavior and integration checks

Band outputs BO1 through BO3 have undefined initial states after power is applied and remain so until data has been transferred. The datasheet cautions that BO1 and BO3 may output the internal clock during this interval. Transfer valid configuration data as soon as the crystal oscillator is operating normally, while respecting the requirement not to send data before oscillator startup.

Before bringing up a tuner design, verify the supply rails, crystal operation, serial timing, divisor calculation, reference-frequency selection, and AM/FM input configuration. Also confirm that output loading and PCB layout follow the device’s stated limits. These checks address the main interactions between digital programming, oscillator startup, and the PLL’s sensitive analog connections.

Conclusion

The LM7001 provides a compact set of PLL, divider, reference-selection, and control functions for AM/FM electronic tuning. Its practical integration hinges on accurate frequency planning, correct serial configuration, a properly designed crystal circuit, and careful treatment of the charge-pump and oscillator layout. Addressing those details early helps engineers evaluate whether the LM7001J or LM7001JM fits the requirements of a tuner design.

Access Official Technical PDF

About The Author