Access Official Technical PDF

Share Summary:LinkedInEmail

Low-frequency harmonics are an important power-quality consideration when electronic lighting is installed across a facility. Compact fluorescent, induction and LED lamps commonly use electronic circuits that include a single-phase rectifier. Because these circuits draw non-sinusoidal current, they can contribute harmonic components to the supply. Yet the combined emissions of several lamps do not necessarily increase in direct proportion to lamp count.

For automation engineers and facility teams, the practical lesson is that single-device compliance testing and real-world system behavior answer different questions. Understanding the difference helps interpret harmonic measurements and assess lighting as part of a broader electrical load.

How electronic lighting produces low-frequency harmonics

Conducted electromagnetic emissions are commonly considered in low- and high-frequency ranges. Low-frequency emissions extend up to 9 kHz, while higher-frequency conducted emissions cover the range from 9 kHz to 30 MHz. In electronic lighting, the rectifier stage is a principal source of low-frequency current harmonics.

A typical electronic ballast receives AC line voltage, filters interference, rectifies the AC to DC and smooths it with a capacitor. An inverter and resonant circuit then provide the conditions needed to start and operate the lamp. The rectifier and input circuitry draw current in pulses rather than as a clean sine wave. Fourier analysis describes that distorted waveform as the fundamental frequency plus harmonic components at integer multiples of the fundamental.

Current harmonics can also distort supply voltage through the impedance of the power source. Where source impedance is low, the resulting voltage distortion may be relatively small even when current distortion is significant. This distinction matters when reviewing power-quality measurements: current THD and voltage THD describe different aspects of system behavior.

What total harmonic distortion tells you

Total harmonic distortion (THD) expresses the combined RMS magnitude of harmonic components relative to the fundamental component, commonly as a percentage. It can be calculated for either current or voltage. A high current THD indicates that the current waveform departs substantially from a sinusoid, but THD alone does not describe every aspect of the load or the absolute amount of harmonic current.

Harmonics can affect other equipment on a power system. In motors and generators, they can increase losses and heating, affect efficiency and torque, and contribute to audible noise or mechanical oscillation. Transformers may experience higher copper, stray-flux and iron losses. Harmonics can also increase stress on capacitors, while voltage distortion may affect electronic equipment that relies on accurate waveform zero crossings.

Why multiple lamps may behave differently

Standardized harmonic-emission measurements assess an individual device under controlled supply conditions. For lighting equipment, IEC 61000-3-2 specifies a measurement method and emission limits. A controlled test supply is required, with voltage and frequency maintained within prescribed tolerances. These conditions make results comparable, but they do not reproduce every installation in which multiple lamps operate together.

Measurements of groups of compact fluorescent lamps found that current THD did not rise proportionally with the number of lamps. Instead, the measured THD declined as lamps were added, with little significant change reported beyond six lamps. This behavior is associated with harmonic summation and cancellation: harmonic components from separate loads can combine differently according to their phase relationships.

Induction lamps also showed a reduction in measured current harmonic distortion as their number increased, with a more pronounced decrease in the reported tests than for compact fluorescent lamps. The results varied by lamp type and circuit characteristics. They should not be taken to mean that adding lamps always reduces harmonic impact; they show why an installation cannot be characterized reliably by multiplying one lamp’s THD by the number of lamps.

Test setup can influence results as well. Supply-cable impedance, including cable inductance and capacitance, may affect harmonic measurements. The reported measurements used short supply cables to limit this influence. When comparing measurements, engineers should therefore consider the test conditions and wiring configuration, not just the headline THD value.

Interpret mixed loads and power factor carefully

A mixed lighting circuit can produce results that are easy to misread. An incandescent lamp contributes little harmonic current, but its fundamental current can be much larger than the harmonic currents from modern lamps. Since the fundamental is the reference value in the THD calculation, adding an incandescent lamp can lower the measured current THD without acting as a harmonic filter. A lower percentage does not, by itself, prove that the system’s harmonic components have been eliminated.

Power factor is another useful but distinct indicator. In the reported measurements, power factor generally increased as more compact fluorescent lamps were connected, then changed little beyond six lamps. Different lamp designs can produce substantially different results. For example, the tested 16 W LED lamp had a reported THD of 16.4% and power factor of 0.955, while a 15 W LED lamp measured 140% THD and a 0.552 power factor. These values illustrate that LED technology alone does not determine harmonic performance; the lamp’s power-conversion circuitry matters.

Power factor correction options

Passive correction can use capacitors and inductors to shape current and filter harmonics, but the required inductors can be too large for compact lighting products. Active power factor correction uses electronic control to modify the current drawn by the load. In an electronic ballast, a boost converter can be placed between the rectifier and input capacitors. It regulates the DC bus while shaping input current to follow the line voltage. This approach requires additional semiconductor components and control electronics.

Practical implications for facility teams

When assessing lighting-related power quality, engineers should distinguish equipment compliance from the behavior of the installed network. Evaluate representative combinations of lamp types where practical, and interpret current THD alongside voltage distortion, power factor and the actual operating configuration. Pay attention to supply impedance and avoid treating a low THD percentage in a mixed load as proof that harmonic currents are absent.

The central takeaway is that electronic lamps can generate low-frequency harmonics, but their combined effect depends on how their harmonic currents sum within the circuit. System-level measurement and informed interpretation provide a more useful basis for managing power quality than assumptions based solely on a single lamp’s test result.

Access Official Technical PDF

About The Author