Access Official Technical PDF

Share Summary:LinkedInEmail

Medium-voltage EV charging offers a potential alternative to fast-charging station designs that rely on a bulky medium-voltage-to-low-voltage (MV-LV) line-frequency transformer. A proposed architecture uses 3.3 kV silicon carbide (SiC) MOSFETs in a medium-voltage dual-active-bridge (DAB) converter to connect more directly to the MV grid and supply an 800 V-class EV charging system. The approach brings power conversion closer to the grid interface, while introducing important design challenges in switching, insulation, and auxiliary power.

Why consider medium-voltage EV charging?

Conventional DC fast-charging stations typically step grid voltage down through an MV-LV transformer, then use an AC-DC stage and an isolated DC-DC stage to deliver controlled power to the vehicle battery. The transformer and associated switchgear, conductors, and foundation requirements can take up substantial installation space. This can complicate deployment where space is limited.

A medium-voltage converter architecture aims to avoid that separate line-frequency transformer installation by interfacing the power converter with the MV grid. This does not mean eliminating electrical isolation altogether: the proposed DAB includes a transformer within its conversion stage. Rather, it changes where and how voltage conversion and isolation are implemented in the charging system.

Wide-bandgap semiconductors, including SiC, are of interest in this context because they support power-conversion designs for higher-voltage applications. The work described in the thesis evaluates 3.3 kV SiC MOSFETs for this role and presents a hardware prototype, testing, and verification of experimental results. The broader target is a charging architecture suited to high-power delivery and 800 V vehicle batteries.

How the medium-voltage DAB converter works

A DAB converter uses an active switching bridge on each side of a transformer. The bridges generate switching waveforms, and a phase shift between them controls power transfer. Transformer leakage inductance participates in this transfer, so its value is a key design parameter alongside the input and output voltages and switching frequency.

In the proposed arrangement, the converter bridges connect across the transformer, with the vehicle-side output intended for an 800 V charging system. The thesis examines the DAB’s voltage, current, and power behavior, along with conditions for zero-voltage switching (ZVS). ZVS is a switching technique in which a device turns on when the voltage across it is near zero. Maintaining ZVS can help manage switching losses, but the operating conditions that permit it depend on the converter’s electrical operating point.

Why a wider ZVS range matters

An EV battery does not remain at a single voltage throughout charging. A converter must therefore handle a range of output voltage conditions rather than only one nominal point. The proposed design uses an extended ZVS scheme intended to support efficient operation across a wider range of battery voltages. For engineers, the key design task is to coordinate phase shift, voltage ratio, inductance, and switching behavior so that the desired power transfer and switching conditions are available across the required operating range.

The thesis also evaluates the effect of leakage inductance on maximum power and ZVS behavior, and considers operation at different switching frequencies. These relationships matter because converter parameters cannot be selected independently: changing frequency or inductance can affect power-transfer capability as well as the ZVS operating region.

Medium-voltage design requires more than device selection

Using a high-voltage-rated semiconductor does not, by itself, resolve the challenges of an MV converter. The circuit board, gate-drive system, insulation, and physical layout must all be designed for the voltage environment. The thesis addresses medium-voltage considerations including PCB clearances and creepage distances, substrate insulation, and an isolated gate-driver architecture.

For system integrators and power-electronics teams, these topics have direct implementation implications:

  • Insulation coordination: board materials and distances between conductive features need to be considered as part of the voltage design.
  • Gate-drive isolation: the driver architecture must provide the isolation required between control circuitry and the switching devices.
  • Layout and packaging: PCB traces, pads, and component placement must account for high-voltage constraints.
  • Operating-range validation: test points should cover relevant voltage, power, and switching conditions, including the battery-voltage range targeted by the charging system.

These requirements make the converter a system-level engineering challenge. Device characterization, circuit design, insulation planning, and hardware testing all contribute to whether a proposed architecture can be implemented as intended.

Auxiliary power: the role of a medium-voltage flyback

A charging converter also needs an auxiliary supply for its control and support circuitry. The thesis evaluates a medium-voltage flyback converter as a candidate for this function, focusing on the high step-down ratio between the MV input and the lower-voltage auxiliary output.

Flyback operation can be analyzed in continuous conduction mode (CCM) and discontinuous conduction mode (DCM). In CCM, the magnetizing current does not fall to zero during each switching cycle. In DCM, it returns to zero before the next cycle begins. The two modes lead to different operating waveforms and design calculations, so the choice affects parameter selection and the converter’s operating range.

The design analysis compares CCM and DCM considerations, including cases with different input-voltage levels, and examines factors such as turns ratio, duty cycle, current stress, switching losses, and magnetizing inductance. The purpose is to inform auxiliary-supply design for an MV charging architecture, not to treat the flyback as a replacement for the main power-transfer converter.

Practical implications for charging-system teams

A medium-voltage DAB using 3.3 kV SiC MOSFETs presents an architecture worth evaluating when transformer footprint and installation complexity are important constraints. Its appeal depends on successfully integrating grid interfacing, isolated power transfer, and battery-voltage flexibility. The accompanying auxiliary supply must also be designed for the system’s high input voltage and support requirements.

For engineers and decision-makers, the central takeaway is to assess the complete conversion chain rather than the semiconductor in isolation. DAB power-transfer behavior, ZVS coverage, transformer and inductance selection, medium-voltage insulation, gate driving, and auxiliary power all shape the design. The work provides a hardware-based evaluation of this approach, while the practical value for a specific charging site will depend on its electrical requirements, installation constraints, and validation needs.

Access Official Technical PDF

About The Author