Access Official Technical PDF

Share Summary:LinkedInEmail

An optical spectrum analyzer (OSA) measures how optical power is distributed across wavelengths. For industrial automation engineers, system integrators and technical decision-makers working with fiber-optic systems, that view can help assess devices, verify communication signals and investigate changes in optical performance. The Anritsu MS9740A is designed for measurements across a range of optical components and systems, from laser diodes and LEDs to wavelength-division multiplexed (WDM) signals and optical amplifiers.

Understanding what the instrument measures—and how settings affect the result—helps teams choose suitable tests and interpret the displayed spectrum. Calibration, fiber handling and operating conditions also matter: measurement quality depends on more than the analyzer alone.

What an optical spectrum analyzer measures

An OSA separates incoming light by wavelength and displays its spectrum. Wavelength is shown on the horizontal axis; the vertical axis represents optical power or a relative level. Depending on the selected display, power may be expressed in units such as watts or dBm, while relative levels may use percent or decibels. The analyzer can display wavelength in air or vacuum, and markers or analysis results may also report frequency.

A spectrum makes it possible to examine the position and level of optical signals, as well as features such as spectral width and side modes. For example, a laser source can be assessed by examining its central wavelength and spectrum characteristics. In a WDM system, multiple wavelength channels share a fiber, so examining the individual signals’ wavelengths and levels supports evaluation of the multiplexed optical signal.

Applications in optical component and system testing

Optical spectrum measurement supports testing across active devices, passive components and communications circuits. The MS9740A manual identifies applications including:

  • Light sources: evaluation of laser diodes, including distributed-feedback and Fabry–Perot types, and LEDs.
  • Passive optical components: loss evaluation for devices such as fibers, couplers, isolators and filters.
  • Optical amplifiers: measurement functions for amplifier gain and noise figure, including tests involving WDM signals.
  • Communications systems: monitoring signal wavelength and level, including checking wavelength-multiplexed signals.
  • Other optical measurements: functions for polarization mode dispersion (PMD) and optical-device analysis.

These applications are relevant wherever a component or circuit must be checked against its intended optical behavior. In production, measurement can support device evaluation; in system work, it can help verify signal characteristics and examine loss or amplifier performance. The exact test method and conditions should match the device and measurement objective.

Resolution, dynamic range and noise

Several instrument concepts shape how a spectrum should be read. Wavelength resolution describes the ability to distinguish nearby optical wavelengths. Resolution settings therefore need to suit the spacing or spectral detail being evaluated. When measuring a narrow-linewidth source, changing the resolution can affect the displayed spectral width; the analyzer’s observed trace reflects both the source and the instrument’s resolution.

Dynamic range concerns the analyzer’s ability to detect a lower-level spectral component near a stronger signal. A strong input can limit detection of nearby weaker light, so the relevant range depends on the measurement conditions and the wavelength separation. Video bandwidth (VBW) is the bandwidth of the internal received amplifier. Narrowing VBW can suppress noise, although settings must be appropriate for the signal. For intense modulated light measured with an external trigger, the manual cautions that VBW should be higher than the modulation signal frequency; a lower VBW can lead to an inaccurate level measurement.

Averaging and smoothing can also reduce the effect of noise on measured levels. Point averaging processes measurements at each wavelength point, while sweep averaging combines results across sweeps. These methods affect data capture and measurement time, so the choice should reflect the purpose of the test rather than being treated as a universal improvement.

Calibration and measurement setup

Calibration helps minimize measurement error by adjusting the analyzer’s internal optical system using a light source with a known wavelength and level. The manual describes calibration before measurement and separate performance-testing procedures. A consistent process should include the required calibration steps and appropriate measurement conditions before results are used for evaluation.

Fiber connections also deserve care. Inspect and clean optical connectors and adapters as needed, and handle fiber cables carefully to avoid compromising the connection. Keep the analyzer’s ventilation openings clear, and use it within its recommended operating conditions. The manual also advises backing up important data, avoiding sudden temperature changes, and not disconnecting mains power while the instrument is on.

Safety and operational considerations

Optical measurement requires attention to laser and electrical safety. Never look directly into the instrument’s optical connector or the end of a connected cable. Use the supplied grounded power cord, and do not connect the instrument to a power supply category outside its stated rating. Service and calibration involving internal components should be left to qualified, authorized personnel; operators should not remove covers or attempt internal repairs.

Routine care contributes to dependable operation. Remove the power cable before cleaning dust around the power supply or fan, and keep ventilation paths unobstructed to reduce the risk of overheating. Follow the instrument’s specified installation and storage guidance, especially where dust, corrosive gases, vibration or condensation may be present.

Applying spectrum measurements effectively

An optical spectrum analyzer provides a practical way to characterize optical sources, examine component loss, assess amplifier behavior and monitor WDM signals. Useful results depend on matching wavelength resolution and other measurement settings to the signal, calibrating appropriately, and maintaining clean, secure optical connections. For plant teams and integrators, treating these steps as part of the test procedure—not as setup details—helps make spectrum measurements more meaningful for device evaluation and optical-system monitoring.

Access Official Technical PDF

About The Author