Access Official Technical PDF

Share Summary:LinkedInEmail

Perovskite LEDs have attracted attention for their potential as solution-processed light sources, but high electroluminescence efficiency depends on more than the semiconductor itself. Defects and interfaces can divert excited carriers into non-radiative pathways, reducing the light produced for a given electrical input. A perovskite-polymer bulk heterostructure (PPBH) design addressed this challenge by combining quasi-2D/3D perovskites with an insulating polymer. The reported devices reached an external quantum efficiency (EQE) of up to 20.1%, while measurements indicated that losses from non-radiative recombination were strongly suppressed.

How the perovskite-polymer emissive layer works

The PPBH emissive layer combines quasi-2D/3D perovskite phases with poly(2-hydroxyethyl methacrylate), or poly-HEMA. In the optimized precursor formulation, the polymer accounts for 20% by weight; the resulting film is estimated to contain 28% polymer and 72% perovskite by volume. The polymer has a wide optical bandgap, while the perovskite phases provide the light-emitting material.

The perovskite is not a single uniform structure. The film contains higher-energy quasi-2D regions alongside lower-energy, more three-dimensional regions. This arrangement creates a pathway for excitations to move toward lower-energy sites, where light emission can occur. The measured photoluminescence (PL) peaks near 795 nm, in the near-infrared, with a full width at half maximum of about 55 nm.

Structural measurements identified quasi-2D/3D crystallites with an estimated average size of 30–55 nm. The crystallites were isotropically oriented in the film, and the measured average surface roughness was approximately 3.3 nm. These details help characterize the material, but the key performance question is how effectively the layer converts excited states into emitted photons.

Perovskite LEDs and the role of recombination

When a device operates, injected electrons and holes can recombine radiatively, producing light, or non-radiatively, dissipating their energy without emission. Non-radiative recombination can occur in the bulk material and at interfaces with charge-transport layers. For an LED, both routes matter: a highly emissive film may still perform poorly if contact layers quench its luminescence.

The PPBH LEDs used a multilayer architecture on indium tin oxide (ITO)-coated glass. A magnesium-alloyed zinc oxide layer served as the electron-transport and hole-blocking layer, with a polyethylenimine interlayer. The approximately 180 nm PPBH film formed the emissive layer. A blend of TFB and PFO polymers acted as the hole-transport and electron-blocking layer; molybdenum oxide and gold formed the top electrode.

This stack produced an electroluminescence spectrum close to the film’s steady-state PL spectrum, with an emission width of about 49 nm. The device structure also supported low-voltage bipolar charge injection. The highest reported EQE was 20.1% at current densities of 0.1–1 mA cm-2, and the reported wall-plug efficiency reached 16.2%. These are device results under the stated measurement conditions, not a demonstration of long-term, high-brightness operation.

What the optical measurements reveal

Optimized PPBH films showed an external PL quantum efficiency (PLQE) of 96±3% under continuous 532 nm excitation at 100 mW cm-2. This indicates that the film converts absorbed optical excitation into emitted light with high efficiency under those conditions. It does not, by itself, establish the efficiency or lifetime of a complete electrically driven product.

Transient measurements help explain the result. After excitation initially forms in the quasi-2D regions, energy moves to lower-energy components in roughly 1 ps. The lower-energy sites then support charge-carrier recombination and emission. This rapid transfer can limit the opportunity for certain loss pathways to compete, though it does not mean that all defects or losses are absent.

Measurements comparing the emissive layer with and without charge-transport contacts found no observable change in its PL decay kinetics. That result suggests that the contacts did not introduce significant additional non-radiative quenching in the tested structure. The late-time PL decay had a lifetime of about 1.5 microseconds, consistent with a low rate of trap-assisted loss at low carrier density or the intrinsic decay of weakly bound electron-hole pairs.

Efficiency depends on light extraction too

EQE reflects both the internal generation of photons and the fraction that escapes the device. Light can be trapped in the substrate or guided along the emissive layer rather than leaving the LED. In this PPBH system, the measured refractive index at the emission peak was 1.9, lower than the value cited for standard halide perovskites. Optical modelling estimated an outcoupling factor of up to about 21%, depending on the emission position in the layer; a value around 25% was possible in the model with an optimized emissive-layer thickness.

The close relationship between modelled outcoupling and measured EQE is consistent with an internal quantum efficiency near 100%, although that internal value is inferred from optical modelling rather than measured directly in the operating device. Lateral PL measurements also showed that light could travel within the emissive layer, raising the possibility that photon recycling contributes to light emission. The study presents this as a potential route for further improvement, not a proven source of additional device efficiency.

Practical limits and implications

Operational stability remains a significant qualification. Encapsulated devices had an electroluminescence half-life (T50) of 46 hours in air under continuous operation at the current density corresponding to peak EQE, 0.1 mA cm-2. The researchers noted that brightness and stability require further improvement for practical applications. A high peak EQE therefore should not be treated as evidence that the device is ready for demanding commercial duty cycles.

For engineers and technical decision-makers evaluating emerging light-source technologies, the findings illustrate why material design, charge-transport interfaces and optical extraction must be assessed together. They also show the value of pairing device-level EQE measurements with film PLQE and transient spectroscopy: each helps distinguish internal recombination losses from contact quenching and photon-extraction limits.

Conclusion

The PPBH approach achieved high-efficiency perovskite LEDs by combining quasi-2D/3D energy transfer with a polymer-containing emissive layer that retained strong luminescence in the presence of charge-transport contacts. Its 20.1% peak EQE is a notable result, supported by near-unity film PLQE and optical modelling. However, the reported operational half-life and the need for further brightness and stability improvements remain central constraints. The practical lesson is to judge emerging LEDs not by peak efficiency alone, but by the interaction of emissive-layer physics, device architecture, light extraction and operating lifetime.

Access Official Technical PDF

About The Author