Access Official Technical PDF

Share Summary:LinkedInEmail

Phosphoric acid fuel cell heat recovery offers a way to generate additional electricity from thermal energy that would otherwise leave the fuel cell system. A modeled configuration combines a phosphoric acid fuel cell (PAFC), a regenerator and a thermoelectric generator (TEG). Its analysis examines not only electrical output, but also energy efficiency, exergy destruction and the influence of the Thomson effect on thermoelectric performance.

How a PAFC-TEG hybrid system recovers heat

A PAFC converts the chemical energy of hydrogen and oxygen directly into electricity, while also producing heat. In the modeled hybrid arrangement, some heat is lost to the surroundings and some is associated with the regenerator. The remaining heat is transferred to the TEG, which converts a portion of it into electrical power. Heat that is not converted is ultimately dissipated to the environment.

The TEG is a solid-state device: it has no rotating or sliding assemblies. Its thermoelectric elements operate across a hot side and a cold side. A temperature difference drives electrical generation through the Seebeck effect. Electrical current through the elements also produces Peltier heating or cooling, while the Thomson effect describes heat absorption or release within a conductor carrying current along a temperature gradient.

Accounting for these effects helps describe the TEG’s heat flows and output more completely than a model that omits Thomson behavior. The analysis also accounts for losses in the PAFC, including activation, ohmic and concentration overpotentials, as well as heat leakage and regenerator losses.

What energy and exergy analysis reveal

Energy efficiency compares useful electrical output with the energy supplied by the electrochemical reaction. Exergy analysis adds a second perspective: it evaluates how much useful work potential is lost through irreversible processes. The study therefore assesses power density, energetic efficiency, exergy destruction rate density and exergetic efficiency. These measures help distinguish simply producing more electricity from using the available energy more effectively.

For the modeled operating conditions, the PAFC-TEG system’s maximum power density is 6.6% higher than that of the standalone PAFC. At the hybrid system’s maximum-power operating point, energetic efficiency is 7.8% higher and exergetic efficiency is 7.7% higher than the corresponding standalone PAFC values. Exergy destruction rate density at that comparison point is 7.8% lower.

These are results from a thermodynamic model, not a guarantee of performance in a particular installation. They indicate the potential value of recovering PAFC exhaust heat under the assumptions and design parameters used. Practical evaluation would require system-specific data and validation.

Why operating current density matters

The PAFC operating current density affects fuel cell output and the amount of heat available to the TEG. The TEG’s electrical current is coupled to the PAFC’s operating condition: it cannot be selected independently of the heat supplied by the fuel cell. In the model, the relationship between the two currents also varies with operating temperature.

The TEG generates power only within a range of PAFC current density. Below the lower boundary or above the upper boundary, its contribution falls to zero in the modeled system. Within the active range, adding TEG output can shift the hybrid system’s performance compared with the PAFC alone. The current density that maximizes hybrid power is not exactly the same as the current density that maximizes standalone PAFC power.

For system designers, this means a TEG should be evaluated as part of the coupled plant, rather than treated as an independent add-on. The study uses maximum power density as its optimization criterion and identifies corresponding operating ranges for power, efficiency and exergy metrics. A different operating objective may lead to a different preferred point.

How the Thomson effect changes the assessment

Including the Thomson effect changes the predicted operating window and performance indicators. In the reported comparison, the model with the effect has a higher lower current-density boundary and a lower upper boundary for TEG power generation. Its maximum hybrid power density is also lower, while exergy destruction at the hybrid maximum-power point is higher, than in the calculation that omits the effect.

This does not mean the effect should be ignored to obtain more favorable results. Rather, it shows why thermoelectric models need to represent relevant heat-transfer mechanisms when estimating system behavior. The study finds that accounting for the Thomson effect gives results it considers closer to actual operating conditions.

Design variables and practical trade-offs

The analysis explores operating temperature, PAFC exchange current density, phosphoric acid concentration and the number of TEG thermocouples. Within the studied cases:

  • Operating temperature: Increasing temperature improves modeled power output, energetic efficiency and exergetic efficiency across the examined current-density range, while reducing exergy destruction rate density. At the maximum-power point, however, the reported efficiencies vary with temperature, so the effect depends on the operating point.
  • Exchange current density: A higher value reduces activation losses in the model and generally improves hybrid-system performance.
  • Phosphoric acid concentration: Increasing concentration in the analyzed cases reduces ionic conductivity and increases ohmic losses, degrading the modeled system’s performance.
  • Thermocouple number: Adding thermocouples affects performance in the range where the TEG produces electricity. The study’s example calculations indicate that the best maximum-power result falls between 20 and 25 thermocouples for the parameters considered; this is not a universal design rule.

Implications for fuel cell system design

A PAFC-TEG configuration can improve modeled power and efficiency by converting part of the fuel cell’s exhaust heat into electricity, but the benefit depends on coordinated choices across the fuel cell, heat-transfer path and thermoelectric generator. Engineers assessing a design should consider the TEG’s active operating range, the PAFC current-density setpoint, thermal losses and the performance measure that matters most to the application.

Including the Thomson effect also matters when comparing configurations or optimizing operating conditions. The practical takeaway is to assess heat recovery with a system-level energy and exergy model that includes relevant irreversibilities, then validate assumptions against the intended design. This provides a more grounded basis for deciding whether thermoelectric generation is a suitable route to improve PAFC system utilization.

Access Official Technical PDF

About The Author