Access Official Technical PDF

Share Summary:LinkedInEmail

Photovoltaic manufacturing scale-up depends on more than achieving a high-efficiency result in the laboratory. Solar technologies must also use materials and processes that can be translated into repeatable production, while maintaining device performance and addressing manufacturing cost. Research reported by the Australian Centre for Advanced Photovoltaics in 2014 illustrates this challenge across silicon cells, emerging thin-film devices and scalable coating methods.

For engineers, system integrators and manufacturing leaders, the central lesson is that cell architecture, material quality and process design need to be developed together. A promising laboratory device is a starting point; a practical manufacturing pathway requires understanding how each fabrication step affects the finished cell and whether that process can be transferred to production equipment.

Photovoltaic manufacturing scale-up starts with process compatibility

Conventional silicon wafer cells were identified as the dominant commercial photovoltaic technology, with continued improvement dependent on reducing manufacturing costs while maintaining or increasing conversion efficiency. One route under investigation is the use of lower-cost solar-grade silicon, including material produced from upgraded metallurgical-grade feedstock. Its potential cost and energy advantages are only useful if cell processing can preserve the material’s electronic quality.

That makes the thermal sequence a critical process-development issue. Research teams adjusted cell fabrication steps to limit the effects of high-temperature processing on carrier lifetime, while retaining the benefits of phosphorus gettering. In particular, the reported approach placed phosphorus diffusion as the final high-temperature step. The broader manufacturing implication is that process order can matter as much as the choice of feedstock: a lower-cost input does not deliver its intended value if downstream processing degrades device performance.

Solar-grade silicon: managing defects through processing

Impurities and defects in silicon can reduce minority-carrier lifetime, which in turn limits cell performance. The report describes work on hydrogen passivation as a way to reduce the impact of these recombination centres. Researchers investigated how controlling hydrogen’s charge state could improve its mobility and reactivity in silicon, and applied the approach to lower-cost material.

Cells made from wafers using 100% solar-grade silicon feedstock reached a certified efficiency of 19.8% in one reported result. A separate highlighted result reported a 20.1% cell, measured at ANU and subsequently confirmed by Fraunhofer Institute testing. These results demonstrate progress in using lower-cost feedstock while retaining strong device performance; they do not, by themselves, establish the economics or production readiness of a commercial process. Further work is needed to determine how consistently material quality and cell performance can be maintained across manufacturing conditions.

For process engineers, this research also illustrates why material characterization belongs alongside fabrication development. Measurements of carrier lifetime, defect behaviour and photoluminescence can help teams understand whether a process change is improving the material or merely shifting where losses occur. Linking those measurements to specific process steps provides a more useful basis for optimization than evaluating efficiency alone.

Scalable coating methods for emerging solar cells

Organic and perovskite photovoltaics offer different material and device approaches from conventional wafer-based silicon. However, laboratory performance does not automatically translate into a scalable manufacturing method. In particular, spin coating has been widely used in research but is not directly transferable to large-area production in the same way as continuous coating processes.

To address this translation gap, CSIRO developed a research-scale solar coater using a slot-die coating head with three-dimensional positional control. The system was designed to support process optimization and simulate aspects of production. It was used to optimize solution-processed organic solar cells, with optimized conditions then translated to larger printed modules.

The coater was also used to develop sequential slot-die coating for perovskite solar cells. The reported work demonstrated printed devices and translated the process to roll-to-roll printing. The practical value of this type of platform is its role as a bridge between laboratory experiments and production-oriented equipment: researchers can test coating conditions in a format that is more relevant to manufacturing before moving to larger-scale systems. The report also notes that improving process reliability remained an area of ongoing development.

Device architecture and manufacturing are connected

Some of the research focused on cell structures designed to improve performance beyond the limits of a single-junction silicon device. Silicon tandem cells combine different photovoltaic materials or cell types to use a broader portion of the solar spectrum. The report describes several approaches, including monolithic and mechanically stacked configurations, and a demonstrated 27.8% ± 1.3% efficiency for a four-terminal silicon/GaAs tandem.

Such results are important for technology development, but tandem designs also bring manufacturing questions. The approaches differ in how layers are combined and what material or crystal-quality requirements apply. Those distinctions influence the fabrication pathway, characterization requirements and eventual integration with production processes. The report’s range of approaches underscores that there is no single route from laboratory efficiency to a manufacturable tandem product.

What manufacturing teams should take from the research

Across these examples, several practical priorities emerge for organizations evaluating photovoltaic process development:

  • Evaluate the whole process sequence. Feedstock quality, thermal steps, passivation and contact formation can interact, so changes should be assessed in the context of the complete cell process.
  • Connect characterization to process decisions. Measurements of defects and carrier lifetime help explain why a device performs as it does and can guide targeted process adjustments.
  • Build in a transfer path early. Coating methods that resemble production processes can make it easier to move promising laboratory conditions toward larger equipment.
  • Distinguish a research milestone from manufacturing readiness. High cell efficiency demonstrates technical potential, while repeatability, process reliability and substantiated cost evaluation remain separate requirements.

Conclusion

Photovoltaic manufacturing scale-up is a coordinated engineering challenge involving materials, device architecture, fabrication sequence and production-compatible processes. Progress with solar-grade silicon shows how process engineering can help lower-cost materials deliver strong cell performance. Slot-die and roll-to-roll coating work demonstrates the value of developing emerging technologies with scale-up in mind, while tandem-cell research highlights the range of architectures still being explored. For industrial decision-makers, the practical priority is to assess performance alongside process transferability, measurement capability and manufacturing cost—not as separate concerns, but as parts of the same technology-development pathway.

Access Official Technical PDF

About The Author