Access Official Technical PDF

Share Summary:LinkedInEmail

Power semiconductors are core components in the converters that control electrical energy across industrial drives, renewable generation, traction and transmission systems. Choosing among IGBTs, diodes, thyristors and other high-power devices involves more than comparing voltage and current ratings. Switching behavior, thermal design, connection method and the consequences of device failure all influence the fit for a particular application.

ABB’s product portfolio illustrates the range of technologies used in these systems, from chip-level IGBT and diode dies to packaged modules and press-pack devices. Understanding their different roles can help engineers and system integrators frame component selection around the demands of the complete converter.

Power semiconductors serve different converter roles

IGBTs are controllable switching devices used in power converters, while diodes provide current paths such as free-wheeling, clamping and rectification. Thyristors are used in applications including controlled rectification and AC power control. Gate turn-off thyristors (GTOs) and integrated gate-commutated thyristors (IGCTs) address high-power switching requirements.

These devices appear across a broad set of applications, including variable-speed drives, uninterruptible power supplies, wind and solar converters, traction equipment, HVDC transmission and flexible AC transmission systems (FACTS). The application and converter topology determine which device characteristics matter most.

IGBTs: switching performance, losses and packaging

IGBT offerings span bare dies and medium- and high-power modules. At chip level, ABB’s SPT+ and SPT++ technologies combine IGBTs with free-wheeling diodes. The source describes SPT+ as reducing conduction losses compared with earlier SPT technology, while SPT++ further develops the carrier profile and, in the 1700 V design described, supports junction operation up to 175 °C. Such technology details matter because conduction and switching behavior contribute to converter losses and thermal requirements.

Module packaging also affects how a design handles heat, current and mechanical stress. Medium-power module families such as 62Pak and LoPak1 are intended for applications including drives, power supplies, power quality equipment, UPS and renewable energy. Their design features include copper baseplates and internal construction intended to support thermal utilization and reliability under cyclic loading.

For higher-power converters, LinPak and HiPak modules are available in different circuit configurations and voltage classes. LinPak’s low-inductance design and separated phase and DC connections support inverter design, while its current-sharing characteristics make it suitable for parallel connection. HiPak modules use aluminum nitride insulation and aluminum silicon carbide baseplates, a material combination described as supporting power-cycling performance. These distinctions can inform choices about layout, thermal paths and module configuration.

Press-pack devices for demanding system architectures

Press-pack construction is relevant when devices are mechanically or electrically connected in series. StakPak IGBT modules use individual spring contacts to apply pressure to chips, helping address the challenge of achieving uniform contact across multiple devices in a stack. The design separates the force applied to each chip from the force required to clamp the overall stack.

Some press-pack applications require a stable short-circuit failure mode. In a redundant series-connected system, a failed device that continues to conduct can allow the equipment to remain in operation while the wider system manages the fault. Whether this behavior is required depends on the application and its protection strategy; it should not be assumed for every press-pack device.

Press-pack diodes and thyristors also serve high-current and high-voltage applications. Rectifier diodes are used in settings such as large AC-drive input stages and traction substations. Fast-recovery diodes support inverter commutation, including free-wheeling, snubber and clamping functions. Their recovery behavior and safe operating area need to match the commutation conditions in the circuit.

Thyristors, GTOs and IGCTs in high-power conversion

Phase-control thyristors (PCTs) are used in applications ranging from DC drives to HVDC converters. A bidirectionally controlled thyristor (BCT) integrates two antiparallel thyristor functions on one wafer. In suitable AC-controller applications, this can replace two PCTs, reducing component count and potentially equipment volume, as described in the product information.

GTOs can be switched off through reverse gate current and are optimized for low conduction losses. They are relatively slow switches and require protective snubber networks to manage current rise during turn-on and voltage rise during turn-off. IGCTs combine thyristor-like conduction with gate-controlled turn-off and are used in applications such as medium-voltage drives, wind converters, marine drives and power-system compensation.

Device ratings alone do not tell the whole story. For high-voltage thyristors, the way blocking voltage is assessed can matter because leakage current and heat generation interact during testing. More broadly, engineers should evaluate voltage exposure, switching conditions, cooling and protection as a connected design problem.

Match device characteristics to the application

A practical selection process starts with the converter’s electrical and operating requirements. Consider:

  • Voltage and current: Establish the required ratings for the device’s position and duty in the circuit.
  • Switching and commutation: Match switching behavior and diode recovery characteristics to the converter topology and operating conditions.
  • Thermal and mechanical design: Account for heat transfer, cycling, mounting and, where applicable, stack clamping.
  • Fault response: Determine whether the system requires a particular failure mode, redundancy or external bypass response.
  • System integration: Consider module configuration, current sharing, connections and the requirements of the gate drive and protection design.

These factors apply across industries, but their priority varies. A traction converter, an industrial drive and an HVDC valve do not impose identical constraints, even when they use related device technologies.

Conclusion: design around the converter

Power semiconductor choices influence converter losses, thermal management, packaging and fault handling. IGBTs, diodes, thyristors, GTOs and IGCTs each address different switching and power-conversion needs, while module and press-pack designs shape how devices integrate into the equipment. For industrial automation teams, the practical approach is to evaluate the device within its complete electrical, thermal and mechanical context, then confirm detailed selection against the relevant product data and application guidance.

Access Official Technical PDF

About The Author