Access Official Technical PDF

Share Summary:LinkedInEmail

Partially premixed combustion (PPC) occupies a middle ground between homogeneous charge compression ignition and conventional diffusion-controlled compression ignition. Fuel is injected early enough to mix with air before ignition, but not so early that the charge becomes completely homogeneous. The resulting in-cylinder stratification—variations in fuel concentration, temperature and flow—can influence ignition timing, heat-release behavior and emissions. Optical diagnostics offer a way to examine these processes and develop more objective measures of stratification.

Why partially premixed combustion depends on stratification

Conventional compression-ignition combustion can produce high efficiency, but its locally rich fuel zones contribute to soot, while high combustion temperatures are associated with NOx formation. Increasing the time available for fuel-air mixing can reduce those rich regions and lower combustion temperature. However, a highly homogeneous charge can ignite rapidly and make combustion phasing difficult to control.

PPC uses direct injection and an extended ignition delay to retain some mixture inhomogeneity. Injection timing affects how long fuel has to evaporate and mix, and therefore shapes the distributions present when combustion begins. That provides a control mechanism unavailable in the same way to fully premixed combustion. The challenge is to find a useful intermediate level: too little stratification can make combustion difficult to control, while stronger local fuel concentrations can change heat release and emissions.

Stratification is not limited to fuel. Temperature and turbulence also vary within the cylinder, affecting how the mixture develops and burns. Combustion stratification is the observed spatial pattern of heat release resulting from these interacting factors.

Optical diagnostics reveal different parts of the process

No single imaging method describes every aspect of PPC. A combination of techniques can connect injection, mixture preparation, combustion and in-cylinder flow.

Shadowgraphy tracks spray development

High-speed shadowgraphy visualizes the fuel spray during injection and evaporation. Side-view images can be used to examine spray penetration and targeting, including whether and when a spray reaches the cylinder liner or piston. Measurements at different start-of-injection timings and injection pressures help show how operating strategy changes spray development.

These observations matter because spray behavior helps determine where fuel is distributed and how much time it has to mix before ignition. The optical access itself can introduce distortion, so appropriate optics and image processing are important when interpreting spray position and penetration.

OH* imaging maps combustion structure

OH* chemiluminescence is light emitted by electronically excited hydroxyl radicals formed through chemical reactions in regions associated with heat release. Imaging this signal provides line-of-sight information about where combustion is occurring. It is widely used as a marker of combustion location, although an image should not be treated as a complete three-dimensional map of the cylinder.

In PPC experiments, OH* images can be used to compare combustion patterns under different injection strategies. The observed combustion stratification is connected to injection timing and mixture preparation. Spectral measurements can also distinguish chemiluminescence from thermal radiation and identify emissions associated with species such as OH*, CH* and C2*.

LIF estimates fuel and temperature distributions

Fuel-tracer laser-induced fluorescence (LIF) provides information about the in-cylinder fuel distribution. In the described work, toluene fluorescence was quantified using its temperature dependence alongside a thermodynamic model. This approach was used to estimate both fuel and temperature distributions, allowing fuel stratification to be compared with combustion images and spectral measurements.

The relationship between fuel distribution and heat release is not necessarily simple: fuel stratification can increase or decrease peak heat-release rate depending on the spatial pattern and local equivalence ratios. This makes measurements of the distribution—not just a single average fuel-air value—valuable when assessing a PPC strategy.

PIV characterizes flow and turbulence

Particle image velocimetry (PIV) measures in-cylinder flow, including velocity fields and cycle-resolved turbulence. Measurements in the piston bowl and squish region can help explain how air motion interacts with injected fuel. Comparing reactive and non-reactive conditions helps distinguish turbulence associated with injection from turbulence associated with combustion.

Flow structures and turbulence influence mixing, which in turn affects fuel stratification and combustion duration. Injector geometry and injection timing are among the factors examined when relating flow behavior to heat release.

Making stratification measurable

Terms such as low, moderate or high stratification are useful descriptions, but they do not by themselves provide a consistent basis for comparing different operating conditions or experiments. An objective metric could help engineers and researchers relate a particular injection strategy to the resulting spatial distribution.

One proposed approach applies a two-dimensional Fourier transform to OH* chemiluminescence images. The transform represents spatial structure across a range of spatial frequencies. With a suitable normalization procedure, information in that range can be used to define a combustion-stratification index. The same general Fourier-based approach can also be applied to measured fuel distributions.

Such an index does not replace the underlying images or explain every cause of a combustion pattern. Rather, it offers a structured way to compare spatial variation across conditions. Its usefulness depends on consistent imaging, processing and interpretation, particularly because optical signals are measurements of specific emissions or tracers rather than direct, unrestricted views of every in-cylinder quantity.

Practical implications for engine development

The combined diagnostic approach provides a framework for tracing how an injection decision affects combustion:

  • Injection and evaporation: shadowgraphy shows spray development and targeting.
  • Mixture preparation: fuel-tracer LIF estimates fuel and temperature distributions.
  • Combustion behavior: OH* imaging and spectroscopy characterize spatial heat-release patterns and spectral emissions.
  • Air motion: PIV measures flow and turbulence that influence fuel-air interaction.
  • Comparison: Fourier-based analysis provides a potential quantitative measure of spatial stratification.

Together, these methods help separate factors that can otherwise be difficult to distinguish. For example, a change in combustion duration may relate to the fuel distribution, the flow field or both. Combining measurements makes it possible to investigate those links rather than relying on injection timing alone as an explanation.

Conclusion

Partially premixed combustion relies on balancing mixture preparation and controllability. Fuel, thermal, combustion and turbulence stratification all contribute to that balance, and their effects depend on how those variations are distributed in the cylinder. Optical diagnostics make these processes observable from complementary perspectives, while Fourier-based indices offer a route toward more consistent comparisons. For engine developers, the practical lesson is to evaluate injection strategies through the resulting in-cylinder patterns and heat-release behavior—not simply by the nominal timing or a qualitative label for stratification.

Access Official Technical PDF

About The Author