For industrial and consumer applications powered by thin-film batteries or energy harvesters, electronic circuits must operate at low voltages without sacrificing reliable switching. Printed polymer circuits offer a potential route to low-cost, flexible electronics, but their performance depends in part on a gate dielectric that can provide sufficient capacitance while limiting leakage and device failures. A parylene-C and poly(methyl methacrylate) (PMMA) bilayer demonstrates one approach: it enabled printed organic transistors and complementary logic circuits with operation down to 2 V.
Why the gate dielectric matters for printed polymer circuits
In an organic field-effect transistor (OFET), the gate dielectric separates the gate electrode from the semiconductor and helps control charge accumulation in the transistor channel. Increasing the dielectric’s capacitance can reduce the voltage needed to switch the device. One way to raise capacitance is to make a dielectric layer thinner, but thinning a polymer film can increase leakage or lead to electrical breakdown.
The researchers addressed this trade-off with a bilayer: an approximately 20-nanometer PMMA layer paired with a thin parylene-C film. PMMA provides a suitable interface for polymer semiconductors, while the parylene-C layer contributes dielectric performance and forms a conformal, pinhole-free coating. The PMMA is also important for n-type devices, where it helps protect the electron-transporting semiconductor from the effects of chlorine atoms in parylene.
In metal-insulator-metal test structures, the bilayer reached an areal capacitance of 19.00 nF/cm² with 120 nm of parylene-C. At 10 V, the average leakage current density for that configuration was 10 nA/cm². Thinner parylene layers could raise capacitance further, but often produced defective capacitors or short circuits. The selected stack therefore balanced capacitance with leakage and fabrication reliability.
Printed top-gate transistors on flexible plastic
The bilayer was incorporated into bottom-contact, top-gate OFETs fabricated on 125-micrometer polyethylene naphthalate (PEN). Source, drain, and gate electrodes were inkjet-printed, as were the semiconductor layers and the injection layer used for n-type transistors. PMMA was spin-coated, and parylene-C was deposited by chemical vapor deposition (CVD). Thus, most functional layers used inkjet printing, while the dielectric stack combined solution coating with CVD.
The top-gate architecture supports control of the semiconductor-dielectric interface and allows gate overlap with source and drain electrodes. The resulting devices used the polymer semiconductor P(NDI2OD-T2) for n-type transistors and 29-DPP-TVT for p-type transistors. Both polarities showed current modulation at voltages as low as 1 V.
To assess repeatability, the team characterized arrays of 100 transistors of each polarity. Across 200 devices, 198 worked, corresponding to a 99% yield. The two failures were associated with particles in the active channel. Most transistors also showed gate leakage below 100 pA; a small number had higher leakage but continued to operate. Average effective mobility was 0.06 cm²/V·s for n-type devices and 0.19 cm²/V·s for p-type devices in the linear regime. These device-level results matter for circuit integration, where variation between transistors can affect logic behavior.
From transistor arrays to complementary logic
Because the p- and n-type transistors were made using the same process and shared the same electrode and dielectric materials, they could be combined in complementary circuits. Inverters operated with supply voltages from 2 to 10 V. At a 2 V supply, their average switching threshold was 1.19 V, and their noise margin was 0.62 V. The devices were sized to account for the difference in drive current between the two transistor polarities.
The circuit demonstrations extended beyond static inverter measurements:
- Seven-stage ring oscillators: These circuits oscillated across the tested supply-voltage range of 2 to 10 V. At 2 V, the average frequency was nearly 6 Hz; at 10 V, it was 57 Hz on average. The best measured stage delay was 1.14 ms at 10 V.
- D-latches and D-flip-flops: A master-slave D-flip-flop, built from two latches, operated at supply voltages as low as 2 V. Its output responds to the falling edge of the clock, making the circuit a basic building block for sequential logic.
The circuits were transparent as well as flexible. Their measured visible-light transmittance was at least 90% including the PEN substrate, and at least 95% when normalized for the circuit alone. Transistor bending tests showed no significant change in p-type performance after 1,000 cycles. N-type performance remained nearly constant through 1,000 cycles at strains below 1%; a small performance loss appeared at 1.1% strain after 1,000 cycles. Non-encapsulated circuits stored in nitrogen remained operational after four months.
Practical implications for system design
The results show how dielectric selection, transistor uniformity, and complementary circuit design must work together to make low-voltage printed electronics viable. A high-capacitance dielectric can help lower operating voltage, but it must also control leakage and support consistent device fabrication. Here, the PMMA/parylene-C stack enabled complementary logic that operated at 2 V, alongside demonstrations of oscillators and memory elements.
For engineers and product teams evaluating printed electronics, the work points to potential uses where flexible, transparent circuitry and low-voltage operation are priorities. It does not replace conventional silicon for every application; rather, it demonstrates a manufacturing approach for adding basic electronic functions to plastic substrates. The practical takeaway is that a carefully engineered polymer dielectric can help move printed OFET technology from individual transistors toward integrated, low-voltage logic circuits.