Access Official Technical PDF

Share Summary:LinkedInEmail

Quantum infrared sensors are not limited to experimental quantum computers or communications networks. Several sensing technologies already use quantum effects in semiconductor materials, while newer approaches aim to measure magnetic fields and form images using individual quantum states. For industrial automation engineers and system integrators, these developments point to new ways of addressing infrared detection, gas monitoring and compact sensing—while also making clear that different technologies suit different measurement needs.

The key distinction is between devices that engineer the behavior of many charge carriers and sensors that prepare and read individual quantum states. Both approaches can improve or extend measurement capabilities, but their maturity, operating requirements and application fit vary.

Quantum infrared sensors: established devices and emerging approaches

Quantum cascade lasers (QCLs), Type II superlattice detectors and quantum well infrared photodetectors (QWIPs) are semiconductor devices built around carefully structured layers. Their performance depends on controlling the energy landscape for electrons within the material. These devices are examples of the first generation of quantum technologies: they use quantum effects collectively rather than relying on the manipulation of a single quantum state.

By contrast, nitrogen-vacancy (NV) centers in diamond use the spin of an electron associated with a specific defect in the crystal. This falls within the newer generation of quantum sensing. Entangled photons, meanwhile, can support specialized imaging and communication methods. These distinctions matter in system design: an infrared camera, a magnetic-field sensor and a quantum imaging arrangement are not interchangeable solutions.

Semiconductor devices for infrared detection

Quantum cascade lasers

A QCL contains a sequence of semiconductor layers that form quantum wells with discrete energy levels. When voltage is applied, electrons move between levels and emit photons. The layer design sets the emission wavelength, and the quantum tunneling of electrons between wells allows a sequence of optical transitions.

QCLs can emit in the mid-infrared, a region relevant to infrared sensing and countermeasure systems described in the source proceedings. The ability to tune the emission through semiconductor design gives developers a way to target particular wavelength ranges. In a sensing system, the practical value depends on the complete optical and electronic design—not simply on the presence of a quantum device.

Type II superlattice detectors

Type II superlattice (T2SL) detectors use alternating semiconductor layers to create engineered energy bands for detecting infrared radiation. Adjusting the layer structure makes it possible to tailor the detector’s spectral response. The proceedings describe designs aimed at different midwave infrared cutoff wavelengths and report focal plane array operation at elevated temperatures compared with earlier operating conditions.

Higher operating temperature can enable the use of smaller cooling hardware and support more compact, lower size, weight and power (SWaP) camera assemblies. This is relevant wherever an infrared instrument must fit within a constrained system. It does not remove the need for thermal management: the detector’s dark current and image performance still vary with temperature.

QWIPs and application-specific response

QWIPs confine electrons in semiconductor quantum wells, enabling infrared detection over a designed wavelength range. The proceedings highlight their uniformity, stability and established manufacturing processes, alongside the limitation of lower overall conversion efficiency. They also describe VGA-format arrays and designs tuned toward the long-wave infrared region, including a detector intended for sulfur hexafluoride (SF6) gas detection.

QWIPs can also be made sensitive to light polarization. Using differently oriented wire-grid structures across neighboring pixels enables a polarimetric detector to capture information about the polarization state of incoming infrared light. That makes polarization an additional measurement dimension, rather than treating it as an unwanted property of the optical signal.

For engineers evaluating an infrared detector, useful selection questions include:

  • What wavelength range must the system measure?
  • What cooling and power constraints apply to the instrument?
  • Does the application benefit from polarization information, or is conventional intensity imaging sufficient?
  • What array format and optical configuration are needed for the system?

Magnetic sensing and quantum imaging

NV centers in diamond offer a different route to sensing. A nitrogen atom next to a vacancy in the diamond lattice creates a defect whose electron spin can be prepared and read using optical methods. Changes in the surrounding magnetic field affect that spin, allowing the defect to function as a very small magnetic sensor.

Unlike superconducting quantum interference devices (SQUIDs), NV-center magnetometers do not require cryogenic cooling, according to the proceedings. Potential uses discussed include magnetic-field measurement, navigation based on Earth’s magnetic field and submarine detection. For industrial users, the broader engineering interest is in whether compact magnetic sensing can support a particular measurement task; the source does not establish a specific factory deployment or performance advantage for process control.

Entangled photons enable another specialized approach: ghost imaging. In this method, one photon interacts with the object while a second, correlated photon is detected. The proceedings describe the possibility of imaging in the mid-infrared while detecting with a camera operating in the visible range. This could be useful where direct detection at the object’s wavelength presents a challenge, though the approach requires a system designed around the photon source, optical path and detection method.

What these technologies mean for system design

Quantum devices do not deliver a universal improvement across all sensing tasks. Their value depends on matching the physical principle to the measurement objective. T2SL detectors and QWIPs address infrared imaging through engineered semiconductor structures; QCLs provide tunable mid-infrared emission; NV centers target magnetic measurement; and entangled photons enable distinctive imaging and communication techniques.

For technical decision-makers, the practical next step is to define the required measurand, spectral range, operating environment, packaging constraints and acceptable system complexity. Then compare the quantum-based component with conventional alternatives at the complete instrument level. Cooling, optics, readout electronics and integration requirements all influence whether a device is suitable for deployment.

Conclusion

Quantum technologies are already present in infrared lasers and detectors, while spin-based magnetometry and entangled-photon imaging represent additional sensing directions. For industrial automation, these developments are best treated as a set of application-specific tools, not as a single replacement for established sensors. Clear measurement requirements and system-level evaluation will determine whether a quantum-enabled component offers a practical fit for an inspection, monitoring or navigation task.

Access Official Technical PDF

About The Author