Energy storage can help balance supply and demand in systems with renewable generation, but connecting a battery or other storage device to a DC bus requires more than a simple voltage conversion stage. Power must flow in both directions: from the bus to charge storage, and from storage back to the bus when power is needed. A quasi-resonant bidirectional converter described in a 2018 electrical engineering thesis addresses this requirement with a two-switch topology designed for soft switching in both operating modes.
The concept is relevant to engineers and system designers assessing DC-DC conversion for energy storage. Its main design interests are reducing the number of active switches compared with a conventional dual-active bridge, limiting switching losses through zero-voltage and zero-current switching, and extending the design through a modular structure for higher-power applications.
Why bidirectional conversion matters in energy storage
Renewable sources such as solar photovoltaic systems and wind turbines can produce variable power. Energy storage provides a way to take in surplus energy and return it when generation is insufficient or demand changes. The converter is the electrical interface between the storage device and the system’s common voltage bus.
Because storage-device voltage is often lower than the bus voltage, the converter must provide suitable step-up or step-down conversion. It must also support charging and discharging without reversing the voltage polarity at either end. In one direction, the converter operates in buck mode; in the other, it operates in boost mode. This makes bidirectional power flow and effective voltage conversion central requirements, rather than optional features.
How the quasi-resonant bidirectional converter is configured
The proposed topology uses two switches to support power transfer in both directions. For comparison, the thesis identifies conventional dual-active-bridge bidirectional converters as using eight active switches. Reducing the active-switch count is a distinguishing feature of the proposed circuit, although the overall suitability of any topology still depends on its application and design requirements.
The circuit uses resonant behavior to shape switch voltage and current during transitions. Inductors and capacitors in resonant converter designs help create conditions in which a switch changes state when either its voltage or its current is near zero. The proposed topology is designed so that both switches can achieve zero-voltage switching (ZVS) at turn-on and zero-current switching (ZCS) at turn-off, without additional auxiliary circuits.
These switching conditions target the losses that occur during hard switching. In a hard-switched device, voltage and current overlap as the switch turns on or off, resulting in switching loss. ZVS reduces the voltage present across a switch at turn-on; ZCS reduces the current present at turn-off. The intended benefit is lower switching loss, particularly as switching events become an important part of converter operation. The thesis presents design equations and operating-stage analysis for the proposed circuit rather than treating soft switching as a control feature alone.
Operation in buck and boost modes
The converter’s operating sequence depends on the direction of energy transfer. In buck mode, power moves from the higher-voltage side toward the lower-voltage side, as in charging a lower-voltage storage device from a DC bus. In boost mode, power moves from the storage side toward the higher-voltage bus. The circuit therefore needs to manage the resonant intervals and switch transitions for each direction.
Understanding these stages is important when translating a topology into a practical design. Component selection and circuit behavior must be considered against the intended input and output conditions, operating power, and switching frequency. The thesis includes design equations, operating-stage waveforms, and simulation studies for both modes. It also compares the proposed approach with a conventional buck-boost bidirectional converter, offering a basis for examining differences in switching behavior.
Simulation, hardware, and modular design
The work evaluates the converter through simulations and a proof-of-concept hardware prototype. The simulations examine a 500 W design at 200 kHz and at 2 MHz, while the prototype provides experimental work for buck and boost operation. These operating points describe the scope of the reported evaluation; they should not be read as a guarantee that the same results apply to other power levels, components, or system conditions.
A further contribution is a modular design approach intended for high-power applications. Rather than treating increased power as a matter of simply scaling one circuit, modular structures combine converter units according to a chosen arrangement. The thesis discusses configurations with series or parallel connections at the input and output and presents a modular topology using the proposed converter. Simulation results and a controller are included for that extended design.
For engineering teams, the modular concept raises practical questions about how the source, storage, and bus are arranged, and how the modules are controlled together. The appropriate configuration depends on system requirements. The available material establishes a design approach and simulation-based evaluation, but does not provide a universal sizing rule for every installation.
Design implications for automation and power systems
In industrial and utility settings, the converter is one part of a broader energy system that may include storage, distributed generation, DC loads, and grid interfaces. Engineers evaluating a bidirectional DC-DC converter should consider the required voltage conversion in each direction, expected power range, switching behavior, and integration with the system’s control strategy. The number of switches and the use of auxiliary circuits are also relevant architectural considerations.
Soft switching can be attractive when reducing switching losses is a design priority, but it does not remove the need for careful circuit design. Resonant behavior, component values, and operating stages must be understood across both buck and boost operation. Likewise, a modular extension should be assessed in the context of the intended power level and electrical configuration, not assumed to be a drop-in solution.
Conclusion
The proposed quasi-resonant bidirectional converter offers a two-switch architecture for energy storage applications, with ZVS turn-on and ZCS turn-off designed into its operation without additional auxiliary circuits. Simulation and proof-of-concept hardware work examine its behavior in both power-flow directions, while a modular version explores an approach for higher-power use. For technical decision-makers, the practical takeaway is to evaluate the topology against voltage, power, control, and integration requirements in both charging and discharging modes.