In industrial and other radiation-exposed environments, an image sensor must continue producing useful signals as its electronics accumulate radiation damage. Research into radiation-hard CMOS image sensors shows that tolerance depends not only on the fabrication process, but also on pixel architecture, layout and operating conditions. Understanding those factors helps engineers assess sensor suitability and identify where performance may change.
Tests of a 0.35-micrometer CMOS process compared three active-pixel designs: N-type, P-type and B-type. The work examined how radiation affected image-sensor output, including leakage current and signal swing. Its central lesson is practical: radiation response is a property of the complete pixel design, not simply a label attached to the process.
Why radiation affects CMOS active pixel sensors
Total ionizing dose (TID) can alter electrical behavior in a CMOS device. In the tested sensors, irradiation increased leakage current, including current associated with the photodiode and pixel circuitry. Leakage is especially relevant in imaging because it contributes unwanted signal, even when the sensor is not receiving light. As that background rises, it can make it harder to distinguish the intended image signal.
The tests also found changes in pixel output swing. Output swing describes the range of signal voltage available from a pixel. A reduction can limit the usable separation between signal levels. In a camera or machine-vision system, that may affect how much margin is available for reading and processing an image, although the consequences depend on the system and its operating requirements.
Radiation response was evaluated by comparing device behavior before and after exposure. The study used a standard CMOS process with a gate oxide thickness of approximately 7.5 nanometers and considered irradiation levels up to about 100 krad. These results describe the tested devices and conditions; they should not be treated as a universal qualification for every CMOS sensor or radiation environment.
Radiation-hard CMOS image sensors: pixel design matters
The three pixel types differed in their photodiode and transistor arrangements. Those structural choices affect how charge is collected and how the pixel’s output is controlled. The tests showed that the designs did not respond identically to irradiation: leakage current and output behavior varied with pixel type.
The B-type pixel combined features of the N-type and P-type designs. In the reported comparison, it offered advantages in both leakage-current behavior and output swing. That finding illustrates why pixel-level design choices deserve attention when selecting a sensor for radiation exposure. It does not mean that one architecture will be best for every imaging application: the required signal range, image quality and operating conditions still matter.
Layout can influence leakage paths
Pixel layout was another important consideration. The study examined spacing and the geometry of photodiode and transistor regions, finding that layout can influence the leakage current associated with a pixel. In particular, the distance between the photodiode and transistor regions affected the measured behavior. Layout is therefore more than a matter of fitting components into a pixel: it can shape the electrical paths that contribute to radiation-induced leakage.
For design teams, this makes it useful to distinguish between process-level and pixel-level considerations. A CMOS process may provide a starting point for radiation tolerance, but pixel structures and their physical arrangement can affect the final result. A sensor assessment should account for both.
Interpreting test results for system design
Radiation tests provide evidence about how a device changes under specified conditions. They do not, on their own, establish performance in every deployed system. Engineers should relate sensor-level measurements to the imaging task and the rest of the signal chain, including the camera electronics and image-processing approach.
When evaluating CMOS active pixel sensors for a radiation-exposed installation, consider:
- Leakage current: Determine how an increase could affect the usable image signal and the system’s ability to separate image information from background.
- Output swing: Check whether changes in pixel signal range leave adequate margin for the intended readout and processing.
- Pixel architecture: Compare the available pixel designs against the application’s imaging requirements rather than assuming a single structure is universally superior.
- Test conditions: Confirm that radiation exposure and measurement conditions are relevant to the intended use. Results from one process or test setup should not be generalized without evidence.
- Layout and integration: Consider how the pixel’s physical arrangement and the surrounding system may contribute to observed performance.
These checks support a more complete assessment than relying on a process description alone. They also help teams identify which parameters need to be monitored during qualification or system testing.
Practical implications for industrial imaging
For system integrators and plant engineering teams, the research highlights both opportunity and caution. CMOS image sensors can be designed to tolerate radiation, and pixel architecture can improve important characteristics such as leakage current and output swing. At the same time, radiation exposure can change device behavior, and the size and direction of those changes depend on the design.
Sensor selection should therefore connect the application’s radiation conditions with relevant device-level test data. Where image reliability is important, evaluate how degradation in leakage current or signal range could affect the complete imaging function—not just the sensor in isolation. The tested pixel designs offer evidence that architecture and layout can shape radiation response, but application-specific validation remains essential.
Conclusion
Radiation tolerance in CMOS imaging is influenced by the fabrication process, pixel architecture and layout. Tests of N-type, P-type and B-type designs found differences in leakage current and output swing, with the combined B-type design showing advantages in the reported comparison. For industrial imaging teams, the practical takeaway is to assess radiation-hard CMOS image sensors using relevant test conditions and system-level requirements, while treating pixel design as a meaningful factor in sensor performance.