Access Official Technical PDF

Share Summary:LinkedInEmail

Radiation-hardened power ICs are expanding beyond voltage conversion to address protection, sequencing and system-level integration. At the 2019 IEEE Nuclear and Space Radiation Effects Conference (NSREC), device makers and suppliers showed how demand from commercial space applications—particularly small satellites—was influencing power-management portfolios. The developments included current limiters and load switches, GaN-based components, converter reference designs and foundational IC building blocks.

For spacecraft engineers and system integrators, the practical theme was a broader choice of ways to balance radiation tolerance, performance, integration and cost. The products and demonstrations described at the conference varied in maturity and radiation assurance, so their suitability depended on mission requirements rather than a single definition of “space grade.”

Radiation-hardened power ICs add protection functions

Power protection has traditionally relied on discrete circuitry, but integrated controllers can reduce the complexity of implementing current limiting and redundant power paths. At NSREC 2019, STMicroelectronics demonstrated the RHRPMICL1A, a radiation-hardened current-limiter controller designed to operate with an external p-channel MOSFET. It was presented as an alternative to discrete implementations for higher-voltage applications.

The controller supports an 8-to-52-V supply range, extendable to 90 V, and offers configurable responses to overload or short-circuit conditions. Its three operating modes—retriggerable, latched and foldback—allow designers to select how the circuit behaves after a fault. Current limit, trip-off and recovery times, and undervoltage protection are also configurable. Depending on the system design, this type of device can serve as a resettable alternative to a fuse or work alongside one.

Other demonstrations addressed switching and bus fault management. Cobham’s UT36PFD103 smart power switch controller was described as supporting load switching, source selection and resettable-fuse functions on 8-to-36-V buses. Its PMBus interface allows an external microcontroller to control the device and receive data. An optional ideal-diode, or ORing, FET can support redundant power architectures.

Texas Instruments also discussed its TPS7H2201-SP single-channel load switch. The device integrates back-to-back FETs, with configurable rise time to help limit inrush current and provide reverse-current protection. These functions matter when powering sensitive downstream electronics or managing multiple sources, but designers still need to verify that voltage, current and radiation requirements align with their application.

GaN options and converter reference designs

Gallium nitride (GaN) was another visible part of the space-power conversation. Freebird Semiconductor showed epoxy-overmolded half-bridge driver modules in its GAM02 series, offered with or without integrated GaN power switches. The company also presented the GAM01 series of low-side gate-driver modules, likewise available with or without integrated switches. These products illustrated a move toward combining driver and power-stage functions in compact modules for commercial space designs.

Intersil presented a radiation-tolerant flyback reference design intended to convert a 28-V system bus to 12 V at power levels up to 24 W. The design combined a radiation-tolerant PWM controller and low-side GaN FET driver with an EPC eGaN FET. The reported efficiency was in the mid-80% range. The components were aimed at low Earth orbit applications where full radiation hardening was not required and cost was an important consideration.

This distinction is important in power-system design: radiation-hardened, radiation-tolerant and commercial components do not represent interchangeable assurance levels. Component selection must reflect the mission’s radiation environment, required reliability and program constraints.

CMOS building blocks target design flexibility

Apogee Semiconductor described a different approach: developing radiation-hardened circuit building blocks using a process based on a conventional CMOS foundry. The aim was to offer designers foundational functions that could be combined into power-conversion or power-management circuits, with the longer-term goal of enabling more complex functions such as PWM controllers and digitally enabled power ICs.

The company reported developing a radiation-hardened oscillator and a reference with an adjustable output from 0.6 to 2.5 V. It also described a rad-hard logic family and a majority voter. These functions can support mixed-signal designs and cold-sparing redundancy, in which components are isolated while turned off. The approach could give customers more flexibility to build application-specific power ASICs, although the availability and qualification status of individual building blocks remain key design considerations.

POL converters and isolated modules keep advancing

Point-of-load (POL) converters and isolated DC-DC modules remained central to space power development. Texas Instruments highlighted the TPS50601A synchronous buck converter, a 3-to-7-V-input, 6-A POL. Compared with the earlier version, the A model offered a wider input range and a p-channel high-side MOSFET that enables 100% duty-cycle operation. The company also reported improvements in reference accuracy and single-event effects performance.

A reference design used four TPS50601-SP devices in parallel to provide 24 A at 0.95 V for a Xilinx KU060 FPGA core. For system designers, this illustrates how converter capability, output accuracy and parallel operation can be considered together when supplying demanding digital loads.

Isolated conversion also addressed higher-voltage buses. Crane Aerospace and Electronics showed its SMP120 series, designed for 80-to-160-V inputs with 180-V transient protection. The series included 28-V and 5-V output versions, with integrated EMI filtering, inrush-current limiting and output overvoltage protection. VPT presented its SGRB series, a 100-V-input converter with a 28-V, 400-W output, an integrated EMI filter and a GaN-based design. At the time of the conference, the product was in preview.

What the developments mean for design teams

NSREC 2019 highlighted a widening set of tools for space power design, from integrated fault protection to GaN power stages, POL converters and configurable circuit building blocks. The benefit is not simply fewer components: integration can change how teams implement protection, redundancy and power distribution, while new converter options address varied bus voltages and loads.

Before adopting any device or reference design, engineers should match its operating range and protection behavior to the electrical architecture, and confirm radiation performance and qualification status against mission needs. The conference’s broader lesson is that space power solutions are diversifying. Choosing among them requires evaluating the complete system—its fault response, redundancy strategy, radiation environment and cost requirements—not just the converter’s headline specifications.

Access Official Technical PDF

About The Author