Access Official Technical PDF

Share Summary:LinkedInEmail

A rail static frequency converter must do more than convert electrical power: it must support stable railway network operation, respond predictably to faults and remain maintainable over a long service life. Multilevel converter designs address these requirements through modular power electronics, coordinated control and provisions for redundancy. ABB’s Rail SFC Light applies this approach using integrated gate-commutated thyristors (IGCTs) and a control philosophy developed for railway static frequency converters.

How a multilevel rail static frequency converter works

Rail SFC Light uses a multilevel topology made up of converter cells. Its power circuit comprises two three-phase legs, each connected to a star point. The three phases of the supplying network connect at the input, while the converter produces the railway network output voltage between the two star points.

Where the converter supplies the overhead contact line directly, an output transformer is not required to produce the necessary contact wire voltage. A line reactor decouples the system and limits possible fault currents. The converter’s output rating can be adapted to project requirements by selecting the number of cells. Additional cells can also provide redundancy in the power-electronics section.

The multilevel arrangement combines the switching activity of individual stages, producing high switching frequencies. This can avoid the need for additional network-side filters in the system. The design can also accommodate filters where particular network conditions call for them.

Efficiency, modularity and fault protection

Rail SFC Light combines a multilevel topology with reverse-conducting integrated gate turn-off thyristors (RC-IGCTs). The integrated diode in an RC-IGCT reduces the number of converter components. The source identifies the combination of RC-IGCT technology and multilevel topology as an important means of reducing losses, while the modular cell design supports project-specific configuration.

Two converter cells are assembled into a Power Electronic Building Block (PEBB), drawing on the PCS 6000 stack concept. Protection measures are built into the stack. A mechanically integrated thyristor switch can short-circuit a cell rapidly in the event of a fault, protecting it. A clamp circuit limits cell-internal fault currents passing through the semiconductors during a stack fault. Together, these features support a robust converter structure and help isolate a defective cell.

Redundancy in the power-electronics section is a design option rather than a substitute for protection. The number of cells and the overall configuration can be selected to meet project needs, while fault-management components address abnormal conditions within the converter.

Control for changing railway network conditions

Railway network protection depends on how the converter behaves during disturbances. In a single-phase short circuit, the transient response should proceed without interruption, with current building up within half a period. The converter is expected to behave as a phase- and frequency-stable sinusoidal voltage source behind its transformer, similar in this respect to a substation transformer or rotary converter.

Control software adapted from ABB’s PCS 6000 experience is intended to preserve this established system behavior in the multilevel design. The control system also supports transitions between interconnected and island operation without interrupting operation or requiring a change of control mode. Island operation is relevant when the railway network is separated from the wider supply system.

The converter does not need to be informed of every change in the rail network configuration. Local or remote subnetworks, other rotating converters and other static frequency converters can be switched on or off. The control system responds to the resulting conditions and regulates frequency, voltage and power according to the active setpoints. The source also describes black-start capability as part of the system’s island-operation functionality.

Installation, safety and serviceability

System layout can be adapted to the site. Hardware, control and water-cooling units are typically housed in a building; other equipment, including chokes, transformers, precharging equipment and heat exchangers, is designed for outdoor installation. The arrangement of main components can be planned around the space available.

Maintenance and safety provisions are equally important in a modular converter. An optional automatic discharge and earthing mechanism can discharge and earth all cells, avoiding the need for personnel to perform manual earthing-rope work on ungrounded converter parts. The open stack arrangement, combined with the clamp choke and bypass thyristor, is designed to limit fault currents and allow a defective cell to be switched out. The source states that explosion protection is not necessary for this arrangement.

The stack provides front-side access to current-converter components, while DC capacitors are accessible from the rear. Individual semiconductor elements can be replaced without interfering with the water cooling: the stack spring is released and the component is removed using a spreading tool. This component-level approach can simplify fault repair and support system availability.

Lifecycle planning and troubleshooting

Long-term planning includes both hardware and control electronics. Platform-based control can support continued spare-parts availability and allow software or interface adjustments as systems evolve. ABB identifies its AC 800PEC platform as the control foundation for this approach and notes that the platform has been actively managed since its introduction in 2004.

For fault analysis, the optional TIMELINE software presents transient-recorder data alongside alarm and event messages through a web browser. Predefined views help users examine events by case, and the tool also provides an interface for testing rail SFC protection systems. Bringing recorded behavior and event information together can help maintenance and engineering teams assess disturbances.

Practical implications for railway power projects

When evaluating a rail static frequency converter, project teams should consider more than conversion efficiency. Cell configuration, redundancy, fault response, island operation, installation constraints, personnel safety and access to lifecycle support all affect the suitability of a system. A multilevel design with integrated protection and established control behavior offers a way to address these requirements within one converter architecture.

For engineers, integrators and operators, the practical value lies in matching the converter configuration to the railway network and site while planning for safe maintenance and future support. These considerations help frame procurement and design decisions around both day-to-day operation and the full service life of the power supply system.

Access Official Technical PDF

About The Author