Access Official Technical PDF

Share Summary:LinkedInEmail

Reactive HiPIMS brings together high-power impulse magnetron sputtering and reactive magnetron sputtering to deposit compound thin films, such as oxides and nitrides. For process engineers, its defining opportunity is not simply the use of high-power pulses in a reactive atmosphere. The ion flux to the target can also be influenced through pulse parameters, making target condition an important control consideration alongside reactive-gas supply and pumping.

Understanding that interaction requires looking at how sputtering, plasma generation and compound formation affect one another. These relationships matter when establishing a deposition process, interpreting changes in discharge behavior or seeking to balance compound-film formation with target sputtering.

From magnetron sputtering to HiPIMS

In magnetron sputtering, energetic ions strike a target and dislodge atoms from its surface. Some of those atoms travel to a substrate and condense, building a film. A magnetic field helps confine electrons near the target, supporting ionization while allowing the discharge to operate at relatively low pressure.

In conventional magnetron sputtering, most sputtered material is neutral. HiPIMS changes the power delivery: instead of applying power continuously, the system applies pulses with high amplitude and a relatively low duty cycle. The resulting dense plasma near the target can ionize a substantial fraction of sputtered atoms and nearby gas species. The plasma therefore supports the discharge and can provide ions that assist film growth.

This distinction is relevant to deposition because charged species can respond to electric fields, unlike neutral atoms. HiPIMS can thus provide a route to influencing how film-forming material reaches a substrate. The extent and consequences depend on the process conditions; the technique does not make every sputtered atom an ion.

Why reactive gas changes the process

Reactive magnetron sputtering introduces a gas, commonly oxygen or nitrogen, that reacts with deposited material to form a compound film. The gas does not interact only at the substrate. It can also react with the target, forming a compound layer on its surface—a condition known as target poisoning.

That layer changes the target’s sputtering yield, or the number of atoms removed per incident ion. Because compound bonds are generally stronger than metal bonds, poisoning reduces sputter yield and can lower deposition rate. The target surface can also have a different secondary-electron emission yield. Since secondary electrons help sustain the discharge, a change in their emission can influence discharge current, voltage, plasma density and other process behavior.

Target condition reflects competing processes. Reactive species can adsorb and chemically bond at the surface, while energetic ions can implant reactive species or drive recoil implantation. At the same time, bombardment sputters material away. The balance between compound formation and removal determines how much of the target is covered.

Reactive HiPIMS and the role of ion flux

Reactive HiPIMS combines the reactive-gas chemistry described above with the pulsed, high-power discharge of HiPIMS. A key process implication is that target state is not determined by reactive-gas partial pressure alone. It also depends on the ion flux reaching the target, which can be controlled through pulse parameters.

This adds a meaningful variable to process development. Reactive-gas flow and pumping establish the gas environment, while pulse conditions influence the discharge and the ions arriving at the target. Those factors act together to determine whether compound formation on the target keeps pace with removal. Adjusting pulse parameters therefore offers a way to influence target condition without treating gas pressure or flow as the only relevant inputs.

The practical objective in reactive sputtering is often to supply enough reactive species to form the desired compound at the substrate while limiting excessive target poisoning. In practice, this balance can be difficult because of process feedback. As the target becomes more heavily covered, the metal flux can fall. The growing film then takes up less reactive gas, which can change the gas pressure and shift the operating state further. This behavior contributes to hysteresis: the process response can differ depending on whether reactive-gas flow is being increased or decreased.

Process considerations for engineers

When assessing a reactive HiPIMS process, it helps to treat the discharge, target surface and gas balance as a coupled system. Relevant considerations include:

  • Target condition: Compound coverage affects sputtering yield and may alter secondary-electron emission.
  • Pulse parameters: These influence the high-power discharge and the ion flux to the target, which in turn affects the target state.
  • Reactive-gas balance: Gas supply, physical pumping and uptake by the growing film all contribute to the process environment.
  • Discharge behavior: Changes in target surface composition can affect electrical and plasma parameters, so operating conditions should be interpreted in context.

Reactive sputtering also presents concerns that pulsed operation is used to help manage. Insulating or poorly conducting deposits on target surfaces can contribute to arcing. Arcs can produce macroparticles that become defects in a coating. In addition, reactive gases such as oxygen can form negative ions; energetic negative ions originating at the target can reach the growing film and cause sputtering or structural damage. Avoiding a poisoned target state can therefore matter for reasons beyond deposition rate.

Conclusion: Treat the target as a process variable

Reactive HiPIMS is best understood as an interaction between pulsed plasma generation, reactive-gas chemistry and the changing condition of the target. Its important process distinction is that ion flux to the target, influenced by pulse parameters, joins reactive-gas partial pressure as a factor governing target poisoning. For engineers and system integrators, this means process development should consider the electrical discharge, gas balance and target surface together. Recognizing those linked variables provides a clearer basis for evaluating operating conditions and troubleshooting compound-film deposition.

Access Official Technical PDF

About The Author