Access Official Technical PDF

Share Summary:LinkedInEmail

A rotary vane vacuum pump can be configured for different demands, from achieving a low ultimate pressure to handling sustained gas throughput or condensable vapours. For engineers and plant teams, choosing the right control settings is only part of the job: oil condition, piping, electrical installation and process hazards also shape system performance. The RV3, RV5, RV8 and RV12 series illustrates how these operating decisions work in an oil-sealed, two-stage pump.

How a rotary vane vacuum pump works

These pumps use sliding vanes in a two-stage pumping mechanism sealed and lubricated with oil. An oil pump supplies pressurised oil to the mechanism, while a sight-glass allows operators to check the oil level and condition. The motor drives the pump through a flexible coupling, and fans provide cooling. An inlet valve closes when the pump is switched off to help prevent air and oil from flowing back into the vacuum system.

Two controls let operators adapt the pump to the application: a mode selector and a gas-ballast control. Their settings affect ultimate pressure, tolerance for inlet throughput and the ability to manage vapours. Because the available performance depends on the pump model and configuration, operating limits should be checked against the applicable technical data.

Choose the operating mode for the process

High Vacuum mode

High Vacuum mode is intended for applications where achieving the best possible ultimate vacuum is the priority. It is also identified for pumping clean gases and clean condensable vapours. In this mode, pressurised oil is supplied to the low-vacuum stage only. For the lowest ultimate pressure, the gas-ballast control is closed, provided the process gas is dry.

High Throughput mode

High Throughput mode supplies pressurised oil to both the high- and low-vacuum stages. It is intended for long-term operation at higher inlet pressures—specified in the manual as above 50 mbar—as well as dirty condensable vapours and oil decontamination. This mode trades ultimate-pressure performance for the ability to sustain higher gas throughput.

The practical choice is therefore application-dependent. A system pumping clean gas toward a low final pressure calls for a different setup from one that must run continuously with higher inlet pressure. Confirm the operating point and pressure requirements before selecting a mode.

Use gas ballast to manage condensable vapours

When vapours enter the pump, they can condense and contaminate the oil. Gas ballast introduces air—or, through a suitable external arrangement, an inert gas—into the low-vacuum stage to help prevent that condensation. The control has three positions:

  • Closed (0): For dry gases and when targeting ultimate vacuum.
  • Low flow (I): For low concentrations of condensable vapours or oil decontamination.
  • High flow (II): For higher concentrations of condensable vapours.

Using gas ballast increases oil loss. Where the process allows, low flow is preferred over high flow to limit that loss. Gas ballast also affects achievable ultimate pressure, so operators should not assume that a setting suited to vapour handling will also provide the lowest pressure.

Plan installation around the whole vacuum system

Good pump performance depends on the inlet and exhaust arrangements as well as the pump itself. The manual recommends keeping the inlet pipeline short and using an internal diameter of at least 25 mm for optimum pumping speed. Support pipelines so they do not load the connections, and use appropriate flexible bellows where needed to reduce vibration transmission. Select an inlet trap when the process involves condensable vapours or substantial dust.

The exhaust must not be allowed to become blocked, and exhaust gases should be directed to suitable treatment where they could be hazardous. An oil mist filter is recommended for operation with gas ballast open, extended operation above 10 mbar inlet pressure, or frequent pump-downs from atmospheric pressure. Leak-testing the assembled system helps prevent both process substances escaping and air entering the vacuum line.

Electrical installation requires the motor to be configured for the supply voltage and the pump to be correctly earthed and protected. Three-phase installations also require correct terminal links and rotation direction. A wrong rotation direction can pressurise the pump and vacuum system; verify rotation during commissioning and stop immediately if it is incorrect. Electrical work and lifting should be handled by appropriately trained personnel using suitable equipment.

Keep safety and maintenance in the operating plan

For flammable or pyrophoric materials, the manual calls for preventing air ingress, maintaining a leak-tight system and using inert-gas purging as required to keep hazardous mixtures below specified limits. Purge flow should be monitored, and the process gas supply stopped if flow falls below the required level. The manual also specifies that the pump should shut down if an inert-gas supply used for dilution fails. These requirements make purge design and interlocking important parts of the system risk assessment, not optional operating preferences.

Routine care starts with checking that the oil level remains between the sight-glass marks. Use the recommended oil for the pump preparation, and inspect oil condition because contamination can affect operation and the ability to achieve the expected vacuum. The maintenance schedule should also address the inlet filter, gas-ballast control, sight-glass, motor fan cover and enclosure. If performance falls short, first consider system leaks, unsuitable measurement equipment, oil condition and whether the selected control settings match the process.

Match pump settings to operating priorities

The practical lesson is to treat the pump, controls and connected piping as one vacuum system. High Vacuum mode and closed gas ballast favour ultimate pressure; High Throughput mode and gas ballast support higher throughput and vapour handling, with trade-offs in pressure and oil consumption. Careful installation, verified rotation, leak testing, appropriate purging and regular oil checks help maintain safe, predictable operation. Always use the technical limits and procedures for the specific pump configuration and process.

Access Official Technical PDF

About The Author