In industrial automation, equipment with different logic and interface requirements may need to exchange data across a serial link. An RS-232 transceiver bridges low-voltage logic signals and the higher-voltage signals used by the interface. The MC145406 is a CMOS device designed for EIA-232-E and CCITT V.28 applications, combining three drivers and three receivers in one IC. Understanding its electrical behavior is important when maintaining or designing equipment around this legacy interface.
What the MC145406 does in an EIA-232 interface
The device performs level shifting in both directions. Its drivers translate logic inputs into bipolar transmit outputs, while its receivers accept interface-level signals and produce logic-level outputs. This arrangement lets a digital system communicate through an EIA-232 connection without requiring separate driver and receiver ICs for each signal path.
The MC145406 has three channels in each direction. Driver inputs, DI1 through DI3, are compatible with TTL logic and also support 5 V CMOS logic. Receiver outputs, DO1 through DO3, switch between ground and the digital supply, VCC. The transmit outputs, Tx1 through Tx3, swing toward the positive supply, VDD, or the negative supply, VSS.
The logic and line-side sections have distinct supply connections. VCC is the digital supply, with a maximum of 5.5 V, and must not exceed VDD. VDD and VSS provide the positive and negative supplies for the line-side circuitry. The documented operating ranges are typically +5 V to +12 V for VDD and −5 V to −12 V for VSS.
Driver voltage, loading, and slew rate
An EIA-232 driver is expected to provide an output between +5 V and +15 V for logic 0 and between −5 V and −15 V for logic 1 when driving a load in the specified range. The MC145406 meets this output-voltage requirement when operated from supplies of approximately ±7 V to ±12 V, subject to the specified load conditions. At ±5 V supplies, its loaded outputs are around ±4 V and therefore do not meet the stated EIA-232 driver voltage requirement. Those levels may still be received by an EIA-232 receiver, but they should not be treated as strict compliance.
The drivers include output current limiting and slew-rate control. The specified maximum slew rate is 30 V/µs. Limiting transition speed is a useful interface characteristic, but designers should still verify signal behavior with the intended cable and load rather than assume that all system-level requirements are satisfied by the IC alone.
When the device is unpowered, the driver outputs have a specified minimum source impedance of 300 Ω under the stated test conditions. This power-off behavior is relevant when connected equipment may remain powered while the transceiver supply is absent. It does not replace checking the complete system’s power sequencing and connection conditions.
Receiver thresholds and noise handling
The receiver inputs are designed to handle EIA-232 signal levels, with an input resistance specified from 3 kΩ to 7 kΩ and a typical value of 5.4 kΩ. With VDD at +12 V and VSS at −12 V, the documented receiver input range extends to ±25 V. This input tolerance does not mean that every voltage is safe under every supply condition: the applicable limits depend on the device ratings and operating configuration.
Receiver thresholds are intentionally separated. The typical turn-on threshold is 1.8 V, while the typical turn-off threshold is 1.0 V, giving approximately 0.8 V of hysteresis. This difference helps prevent a noisy or slowly changing input near the switching point from causing repeated output transitions.
For EIA-232 signaling, a sufficiently negative input is interpreted as a mark and produces a logic 1 at the receiver output. A sufficiently positive input is interpreted as a space and produces a logic 0. An open or grounded receiver input is interpreted as a mark, driving the corresponding digital output high. These defined states can matter when assessing disconnected cables or unused channels.
Practical design checks
When incorporating the MC145406 into a legacy serial interface, review the full electrical conditions rather than relying on nominal signal labels. Key checks include:
- Supply compatibility: Confirm the positive and negative line-side rails and ensure VCC does not exceed VDD.
- Driver loading: Check output voltage against the connected load, especially when operating from ±5 V supplies.
- Receiver limits: Keep Rx inputs within the permitted range for the selected supplies and observe the specified input resistance.
- Logic connections: Keep DI and DO signals within the digital supply and ground range; do not connect high-voltage Tx outputs directly to TTL inputs.
- Unused inputs: Tie unused DI inputs to an appropriate logic level and unused Rx inputs to ground, as recommended in the device documentation.
- Power sequencing: Consider conditions where one supply is present while another is absent. The application guidance describes optional diodes for particular supply arrangements.
The device documentation also describes external components for power-supply and ESD protection. Such circuits must be evaluated for the actual installation and operating conditions; the presence of internal protection circuitry is not permission to exceed maximum ratings.
Applying the device in legacy automation systems
The MC145406’s combination of three transmit drivers and three receive channels can support multi-signal serial connections that require EIA-232-level translation. Its separate logic and line-side supplies allow the digital section to operate from a 5 V rail while the interface section uses bipolar supplies. That separation is useful to understand when troubleshooting a board, selecting replacement components, or documenting a control system’s communication path.
As with any legacy interface component, the practical design decision depends on the exact electrical requirements of the connected equipment. Verify supply rails, signal polarity, loading, input limits, and behavior during power transitions against the device specifications and the rest of the system.
Conclusion
The MC145406 integrates three EIA-232 drivers and three receivers, with TTL-compatible inputs, slew-rate-limited outputs, wide-range receiver inputs, and hysteresis for improved rejection of threshold noise. Its performance depends on appropriate bipolar supplies and loading: operation at ±5 V does not provide the specified EIA-232 driver output voltage, while higher supply levels within the documented range can meet that requirement. For industrial teams maintaining legacy serial links, careful checks of signal levels, grounding, power sequencing, and input limits are essential to applying the device reliably.