Access Official Technical PDF

Share Summary:LinkedInEmail

A soft-switching PFC converter combines power-factor correction (PFC) with switching transitions designed to reduce the overlap of voltage and current in semiconductor devices. This matters in AC-DC power supplies because higher switching frequencies can support improved power density, but hard switching can increase switching losses and electromagnetic interference (EMI). A proposed boost-converter design addresses this trade-off by coordinating zero-voltage and zero-current transitions across its main and auxiliary devices.

Why soft switching matters in PFC

Nonlinear loads and power-electronic converters can draw harmonic currents from the grid. PFC converters are used to reduce reactive power and total harmonic distortion (THD), helping manage the input current drawn by an AC-DC system. A boost topology is commonly used for high-frequency PFC applications.

Increasing switching frequency can create design benefits, but it also makes switching loss and EMI important considerations. In a hard-switched device, voltage and current may overlap during turn-on or turn-off. Soft-switching methods shape the transitions so that a device changes state when either its voltage or current is near zero.

Two techniques used in the proposed converter are zero-voltage transition (ZVT), which supports turn-on at zero voltage, and zero-current transition (ZCT), which supports turn-off at zero current. The design applies these techniques to the main switch while also using zero-voltage switching (ZVS) and zero-current switching (ZCS) for the main diode.

How the soft-switching PFC converter operates

The circuit retains the basic boost-converter power stage: an input filter inductor, main switch, main diode and output capacitor. An auxiliary snubber cell adds an auxiliary switch, resonant inductor and capacitor, diodes, and an auxiliary transformer. These components shape current and voltage transitions around the main switching events.

Rather than changing state abruptly, the converter moves through a sequence of resonant operating stages during each switching cycle. The auxiliary cell helps prepare the conditions for the main switch and diode to change state under soft-switching conditions.

Turn-on and energy transfer

At the start of the cycle, the auxiliary switch is activated. The resonant elements change the current flowing through the main diode until it falls to zero, allowing the diode to turn off with ZCS. A subsequent resonance reduces the voltage across the main switch’s associated capacitance. When that voltage reaches zero, the switch can turn on with ZVT.

During these early stages, energy from the resonant capacitor is transferred through the auxiliary transformer, with most of that energy delivered to the output. This direct transfer is a key feature of the design: it allows the snubber cell to support switching transitions while reducing the current burden on the auxiliary switch.

Turn-off and recovery

Later in the cycle, the auxiliary switch is activated again to redirect current away from the main switch. Once the main-switch current falls to zero, its control signal is removed, enabling ZCT turn-off. The resonant stages then restore the conditions needed for the next cycle. The main diode turns on with ZVS and turns off with ZCS, while the auxiliary switch also turns on and off with ZCS.

According to the proposed topology’s analysis, these transitions do not add current or voltage stress to the main semiconductor devices. The design also uses a common ground, which simplifies the converter’s control arrangement compared with snubber cells whose auxiliary switches do not share a common ground.

Design considerations for engineers

Soft switching depends on selecting resonant-component values and timing so the required transitions occur within the switching cycle. The design procedure sets several relationships and timing conditions:

  • The first resonant-inductor value should be at least twice the second resonant-inductor value to support ZCS turn-off of the auxiliary switch.
  • The auxiliary transformer’s secondary turns are specified between one and 1.5 times the primary turns; a higher turns ratio reduces energy transferred to the output.
  • The ZVT interval must be longer than the main switch’s rise time, and the ZCT interval must be longer than its fall time.
  • The resonant current must reach the required level within the auxiliary switch’s rise time to support its ZCS turn-on.

These are design constraints, not guarantees of performance in every implementation. Component selection, switching timing and operating conditions must be considered together when adapting the topology to a particular PFC application.

Prototype results and practical interpretation

An experimental prototype was built for 220 V AC input, 400 V output, 500 W output power and a 100 kHz switching frequency. The reported line measurements at full load were a power factor of 99.7% and THD of 3.9%. The experimental comparison also reports approximately 97.1% efficiency at nominal output power for the soft-switched converter, compared with about 93% for the hard-switched converter.

These results provide evidence for the design under the tested prototype conditions; they should not be treated as a universal efficiency or power-quality specification. The study also reports operation across a range of line voltages and output currents, but an implementation still requires validation against its own load profile and electrical requirements.

Conclusion

For engineers evaluating an AC-DC boost PFC stage, the proposed soft-switching approach offers a coordinated way to manage switching transitions: ZVT turn-on and ZCT turn-off for the main switch, ZVS turn-on and ZCS turn-off for the main diode, and ZCS operation for the auxiliary switch. Its auxiliary transformer transfers much of the switching energy to the output, while the common-ground arrangement supports simpler control. The practical takeaway is to assess the full resonant network, timing conditions and measured operating results—not just the switching technique—when deciding whether this topology fits a power-conversion design.

Access Official Technical PDF

About The Author