Access Official Technical PDF

Share Summary:LinkedInEmail

Thermoreflectance imaging can make localized heating visible as electromigration develops in an electrical interconnect. That matters to engineers assessing aluminum interconnect reliability: a device’s overall resistance may rise as damage accumulates, but a resistance measurement alone does not show where current is concentrating or where a failure may begin. In tests of an asymmetric aluminum line containing a void-and-reservoir pair, spatial temperature measurements revealed hot spots and strikingly different failure locations under opposite bias polarities.

Why electromigration needs spatial monitoring

Electromigration occurs when current flow drives metal atoms through an interconnect. Momentum transferred from moving electrons can displace atoms, encouraging material to accumulate in some locations and leave voids in others. With enough damage, a void can interrupt electrical continuity; material accumulation can also create features that threaten circuit operation.

As interconnect dimensions shrink, current density and local variations in current flow become important reliability concerns. Geometry can contribute to current crowding, particularly at transitions between narrow wires and wider contact pads or around constrictions. These regions can generate concentrated Joule heating. Temperature, current distribution and evolving structural damage can interact, so observing the location and development of a hot spot may provide information that a single device-wide resistance reading cannot.

How thermoreflectance imaging maps hot spots

In thermoreflectance imaging, electrical pulses heat the test structure, changing the metal’s reflectance. By comparing reflected-light images taken during heated and reference portions of the pulse cycle, the method produces a spatial map of temperature change. In the reported measurements, the aluminum device was illuminated and imaged with a camera while electrical conditions were monitored. The resulting maps showed how heating changed as the applied voltage increased.

This approach provides a way to observe temperature across a region rather than measuring one point at a time. The measurements are temperature changes relative to room temperature, not a direct map of atomic movement. Their value is that hot spots can indicate where local current density or device structure may be changing during electromigration stress.

What the asymmetric test structure revealed

The test line was made from aluminum and included an intentionally designed void next to a reservoir, with contact pads at its ends. The reservoir was intended to act as a nearby source of material that might help replenish a developing void. The structure was asymmetric, so reversing the voltage changed the relationship between current direction and the void-reservoir geometry.

With forward polarity, imaging showed hot spots developing both near the void and at the narrow transition between the interconnect and a contact pad. The test line eventually failed at the pad connection. After failure, microvoids were also observed around the designed void. This outcome is consistent with the possibility that the reservoir helped preserve the central section in this polarity, but the pad failed first; the tests therefore did not establish a quantified improvement in the void’s lifetime.

With reverse polarity, a hot spot developed near the void and the line failed in that region rather than at the pad. Failure occurred at a lower current density than in the forward-polarity test. The contrast shows that the same physical layout can exhibit different electromigration behavior when current direction changes. A reservoir’s potential benefit should therefore not be assumed to be independent of polarity or geometry.

Why temperature patterns and failure sites differ

The experiments point to several interacting influences: electron-wind forces associated with current, gradients in atom concentration and temperature gradients. Their relative effects depend on the local structure and current direction. A reservoir may provide material near a void, while current crowding at a pad transition creates a separate location of concern. Hot spots can also coincide with evolving damage: as microvoids change the conducting geometry, current can redistribute, potentially concentrating heating further.

In both polarities, some hot-spot temperatures rose beyond what would be expected from the general increase in Joule heating across the device. The authors linked this behavior to local structural changes and altered current distribution. The highest-temperature location was not necessarily the point that failed first. This is a practical reminder that peak temperature alone may not identify the most vulnerable site; geometry, temperature gradients and damage evolution also matter.

Implications for interconnect reliability work

For engineers and reliability teams, the findings highlight the value of looking beyond average electrical measurements when investigating electromigration. Spatial thermal imaging can help identify where to focus inspection and testing, especially in designs with constrictions, pad transitions or material reservoirs. Polarity should be treated as a test condition, not just a wiring detail, when an asymmetric layout may respond differently to current direction.

  • Assess local geometry: Examine narrow-to-wide transitions and constrictions as potential current-crowding sites.
  • Compare both polarities: Test whether reversing current changes hot-spot locations or failure modes.
  • Track temperature over time: Changes in a localized thermal pattern can provide clues about evolving damage.
  • Interpret maps alongside electrical data: Combine spatial temperature observations with resistance, current and voltage measurements rather than treating any one indicator as conclusive.

Conclusion

Thermoreflectance imaging provides a spatial view of heating as electromigration progresses, revealing behavior that aggregate resistance measurements may not locate. In the tested aluminum structure, bias polarity changed whether failure occurred at the contact-pad transition or near the void. The practical lesson is that interconnect reliability depends on local geometry and evolving conditions as well as overall electrical stress. Thermal maps can strengthen failure analysis and guide further testing, while additional investigation is needed to establish how reservoir designs perform across other structures and operating conditions.

Access Official Technical PDF

About The Author