Access Official Technical PDF

Share Summary:LinkedInEmail

Choosing a three-phase brushless motor driver IC involves more than matching the motor phases. Engineers must also consider commutation inputs, speed-control behavior, current feedback, signal conditioning, and protection. The LB1854M brings these functions together in a driver intended in particular for VCR capstan and drum motors. Its design combines 120° voltage-linear drive with soft switching, built-in frequency-generator (FG) amplifiers, and configurable control gain.

For system integrators and equipment designers, the device is a useful example of how drive, control, and monitoring functions can be consolidated in one IC. Its electrical limits and pin-level behavior also show the external design decisions required to use it appropriately.

Drive architecture and three-phase commutation

The LB1854M drives a three-phase brushless motor through U, V, and W output pins. Its Hall amplifier inputs accept the corresponding phase signals, with each input interpreted by comparing a pair of pins: a logic-high phase state occurs when input 1 is at least 0.2 V above input 2, and a logic-low state when it is at least 0.2 V below. The resulting phase states determine which motor phases source and sink current.

Forward and reverse operation is selected through the FRC control pin. The specified low level is 0.7 V or less, and the high level is 2.3 V or more. The datasheet’s commutation table maps combinations of U, V, and W Hall states to the source and sink phases for each direction. Engineers should use that table, together with the motor’s Hall-sensor sequence and wiring, when validating rotation and commutation.

The device uses a 120° voltage-linear drive technique. In practical terms, this describes the driver’s approach to controlling output voltage across the motor phases; it is not a substitute for checking the motor-specific commutation pattern and operating requirements.

Soft switching and speed control

The LB1854M’s soft-switching scheme is intended to allow smaller external capacitors, including chip capacitors. This can influence component selection and board layout, but the datasheet does not specify a universal capacitor value: the surrounding circuit and application determine the appropriate implementation.

Speed control is voltage-based. The voltage applied to the VC pin controls the output voltage, while the VC REF pin sets the control start voltage. The specified control-start threshold is 2.5 V when the output peak-to-peak voltage is 2 V. A capacitor connected from the FC pin to ground can lower the control amplifier’s gain-frequency characteristics to help prevent oscillation.

The GC pin selects between two control-output gain levels. The datasheet gives high gain as 40 dB typical and low gain as 34 dB typical. At a 5 V VCC2 supply, the pin-level guidance specifies 0–1 V for 40 dB and 4–5 V for 34 dB. With the input open or at the stated middle level, the gain is 40 dB at low speed and 34 dB at high speed. Because behavior depends on the described conditions, control-pin implementation should follow the datasheet rather than treating the middle state as a single fixed gain.

Current feedback and built-in protection

The Rf pin supports current feedback to the control amplifier. A resistor between Rf and ground can convert output current into a voltage for detection. The IC’s current limiter operates when the voltage at Rf reaches the externally established voltage on the CL pin. In other words, the current-limit threshold is set through the external circuit; designers need to account for the sensing resistor, CL voltage, and intended operating current together.

Thermal shutdown is also built in. The listed shutdown operating temperature has a 150°C minimum, 180°C typical, and 210°C maximum, with 15°C hysteresis specified as a design target. These figures describe protection behavior, not a recommended normal operating temperature. Thermal design should keep the IC within its stated operating conditions and account for dissipation in the actual assembly.

FG signal conditioning and electrical limits

For speed-related feedback, the device includes an FG amplifier and a Schmitt amplifier. The FG input pins accept the signal, while FGOUT1 and FGOUT2 provide the amplifier and Schmitt outputs, respectively. The datasheet specifies a typical open-loop voltage gain of 60 dB at 1 kHz and 22 mV Schmitt hysteresis for both transitions. This integrated signal conditioning can reduce the need for separate amplification stages, subject to the signal levels and interface requirements of the application.

At 25°C, the stated operating supply ranges are 5–18 V for VCC1 and 4.3–6.5 V for VCC2. The output voltage rating is 22 V, and the maximum output current rating is 1.5 A. These are ratings and should not be interpreted as a guarantee that every combination of supply, load, and thermal conditions is suitable. The datasheet also lists output saturation voltage of 1.6–2.2 V at 0.5 A and 2.0–3.0 V at 1.0 A, with source and sink contributions combined.

VCC1 supplies the drive outputs; VCC2 powers the other blocks and is required to be stabilized against ripple and noise. This separation makes supply planning an important part of circuit design, especially where drive switching could affect control or sensing behavior.

Applying the LB1854M in a design

Before integrating this three-phase brushless motor driver IC, engineering teams should verify the complete interface and operating envelope:

  • Match the U, V, and W Hall-input sequence to the motor’s phase wiring and confirm forward/reverse behavior.
  • Set VC and VC REF levels for the intended speed-control range and start behavior.
  • Choose the Rf sensing resistor and CL reference voltage to establish the required current-limit response.
  • Provide stable VCC2 and evaluate the FC capacitor if control-loop frequency behavior requires adjustment.
  • Check supply, output-current, output-voltage, dissipation, and ambient-temperature limits against the actual operating conditions.
  • Confirm that the FG signal and Schmitt output are compatible with the receiving control circuitry.

The LB1854M integrates phase drive, voltage-based speed control, gain selection, FG signal conditioning, current limiting, and thermal shutdown in a single device. Its practical value depends on correctly configuring the external sensing and control components and respecting the specified electrical limits. For engineers assessing a legacy or application-specific motor-control design, the datasheet’s pin functions and commutation table are essential references for determining whether the IC fits the motor and system requirements.

Access Official Technical PDF

About The Author