Ultrasonic pretreatment can improve the flotation of a single sulfide mineral by removing oxidized material and contaminants from its surface. In mixed-mineral circuits, however, the same treatment may have the opposite effect. Tests on galena showed that pretreatment increased recovery when galena was treated alone, but reduced recovery when galena and pyrite were sonicated together. For mineral processing engineers, the distinction highlights why pretreatment should be evaluated against the actual ore and mineral associations—not only on isolated components.
How ultrasonic pretreatment affects mineral surfaces
Ultrasound can produce acoustic cavitation in a liquid. Pressure changes in the sound field cause small bubbles to form, oscillate and eventually collapse. Their collapse creates localized forces, including liquid micro-jets, that can erode particle surfaces and dislodge contaminants. In flotation, surface cleaning may help collectors adsorb and make particles more amenable to attachment to air bubbles.
That mechanism can be beneficial when the target mineral is treated on its own. But cavitation can also influence chemical reactions in the slurry. When different sulfide minerals are present together, their electrochemical interaction may change how each mineral oxidizes or dissolves. The net effect on flotation therefore depends on both physical cleaning and the chemistry occurring at the mineral surfaces.
Galena flotation improved when galena was treated alone
In the reported tests, single galena was sonicated for five minutes at 40 kHz before flotation. With the collector DDTC at 10 mg/L, recovery rose from 85.78% for untreated galena to 91.50% after ultrasonic pretreatment. At 20 mg/L DDTC, recovery increased from 88.72% to 92.74%.
The researchers attributed the improvement mainly to removal of oxidized components and contaminants from the galena surface. A cleaner surface can support reagent adsorption and improve particle hydrophobicity, an important property for flotation. These results describe the tested conditions; they do not establish that ultrasound will improve recovery for every galena ore or operating setup.
Why galena–pyrite mixtures responded differently
The outcome changed when galena and pyrite were mixed before sonication. The study compared two procedures: treating galena and pyrite separately before combining them, and treating the minerals together in the same slurry. Separate treatment produced substantially better galena separation than joint treatment. At a DDTC dosage of 10 mg/L, the separately treated mixture yielded a concentrate with 74.22% lead grade and 91.21% lead recovery. When the minerals were sonicated together, lead grade was 68.78% and recovery was 41.12%.
Galena is electrochemically more active than pyrite in this mineral pair. When the minerals are in contact, galena acts as the anode and pyrite as the cathode in a galvanic interaction. The study’s analyses indicated that joint ultrasonic pretreatment intensified this interaction and increased galena dissolution. In turn, oxidation products formed on the galena surface, including lead sulfate (PbSO4) and lead hydroxide (Pb(OH)2).
These surface products matter because they can reduce galena’s hydrophobicity and interfere with the flotation response. ICP-OES measurements found a higher concentration of dissolved lead after the mixed minerals were sonicated than after galena was treated alone. X-ray photoelectron spectroscopy (XPS) also showed changes consistent with increased oxidation and the formation of lead compounds on the galena surface. Together, the flotation and surface analyses support a different outcome in the mixed system: ultrasound can clean particles, but it can also accelerate reactions that hinder flotation.
Particle size changes the effect of pyrite
The influence of pyrite was not the same across the particle sizes tested. Galena recovery was affected most when pyrite particle size was similar to galena’s 38–74 µm size range. The coarser pyrite fraction, 74–150 µm, had the least influence, while the finest fraction, below 38 µm, fell between the two in its effect on recovery. Lead grade also showed a downward trend as pyrite particle size decreased.
The proposed explanation is that particle size changes the relative surface areas of galena and pyrite in contact. That ratio can influence the rate of their electrochemical reaction. The study associated a surface-area ratio closer to 1:1 with faster interaction and more severe oxidation of galena. It also noted that finer pyrite could contribute to hydrophobic agglomeration and mechanical entrainment, affecting concentrate grade. Particle-size effects are therefore relevant both during pretreatment and in interpreting flotation results.
Practical considerations for process evaluation
For plant teams and process-development groups, the findings point to several considerations before adding ultrasound to a flotation flowsheet:
- Test the mineral assemblage: Results from a single-mineral test may not predict behavior when sulfide minerals are sonicated together.
- Compare pretreatment sequences: Treating minerals separately and then combining them produced a different result from sonication of the mixed slurry.
- Include particle-size distribution: The relative sizes of galena and pyrite affected recovery and concentrate grade.
- Assess surface chemistry as well as recovery: Dissolved ions and surface analysis can help identify whether changes reflect cleaning, oxidation or galvanic interaction.
The experiments used a defined laboratory setup, including a five-minute pretreatment and a 40 kHz transducer. The authors identified ultrasonic power, frequency, intensity and treatment time as areas requiring further study, as well as the response of other polymetallic sulfide systems. The reported results should therefore be treated as evidence of a process-dependent effect, not as a universal operating recipe.
Conclusion
Ultrasonic pretreatment can support galena flotation when it cleans a single-mineral surface, yet reduce recovery when galena and pyrite are treated together. In the mixed system, intensified galvanic interaction and the formation of oxidized lead compounds were associated with lower galena hydrophobicity and recovery. For industrial mineral processing, the practical lesson is to evaluate ultrasound using representative mineral mixtures, particle sizes and pretreatment sequences, while monitoring both flotation performance and surface chemistry.