Access Official Technical PDF

Share Summary:LinkedInEmail

A 3D-printed phased-array antenna can bring together components that would traditionally be manufactured separately and joined into a larger assembly. A demonstrated Ku-band design integrates a four-element antenna array with its beamforming network in a polymer-based structure, using additive manufacturing for complex waveguide geometry and mechanically adjustable dielectric inserts for beam steering. The result highlights an approach to RF subsystem design that may be relevant wherever part count, assembly complexity, weight, and manufacturing turnaround matter.

Integrating the antenna and beamforming network

Phased-array antennas steer a beam by controlling the relative phase of signals delivered to multiple stationary radiating elements. A complete system therefore needs more than the antennas themselves: it also requires a feed network, power splitters, phase-control sections, waveguide bends, twists, and interconnects.

In conventionally machined metal-pipe rectangular waveguide systems, these components are often made as separate parts. Joining them can require multiple flanges, each adding an interface to the assembly. The reported design instead combines 26 circuit elements into a single subsystem: one flange, six mitred bends, three power splitters, four tunable delay lines, four waveguide twists, four bent interconnects, and four H-plane sectoral horn antennas.

The subsystem uses WR-62 waveguide and was optimized for operation from 15 to 17 GHz, within the Ku band. Its single input port feeds four antenna elements through a corporate feed network. The integrated geometry reduces the need to assemble numerous individual waveguide components, while taking advantage of additive manufacturing’s ability to produce complex three-dimensional forms.

How the 3D-printed phased-array antenna steers its beam

Beam steering depends on creating a phase difference between neighboring antenna elements. In this design, that difference is adjusted using four movable ABS dielectric inserts. Each insert slides into a waveguide section, changing the effective dielectric loading and, in turn, the guided wavelength and signal phase through that section. Adjusting the inserts changes the relative phase across the array and shifts the direction of the radiated beam.

The distinction between phase shifting and time delay is important in beamforming. A true phase shifter maintains a different phase relationship across frequency than a true delay line. For wideband beamforming, true time delay can help avoid beam squint, in which the steering direction varies with frequency. The designed phase-shifting sections showed frequency-dependent behavior: they approximated a true phase shifter near the lower band edge and a true delay line near the upper edge, with a transition region between.

The delay-line inserts were designed with elliptically tapered ends to improve simulated insertion- and return-loss behavior. Their brackets used a screw mechanism and guide rails to support controlled, even movement. At maximum insertion, the design predicted relative phase shifts of 262 degrees at 15 GHz and 288 degrees at 17 GHz; measured values were 263 and 290 degrees, respectively.

Combining PolyJet, FDM, and metallization

Different manufacturing processes were selected for different parts of the subsystem. Industrial PolyJet printing produced the main waveguide body from VeroWhite resin. The top and bottom halves were printed separately to make cleaning and metallization more manageable. PolyJet’s ability to form intricate features supported the bends, twists, and other complex internal paths.

Lower-cost fused deposition modeling (FDM) produced the dielectric inserts from ABS, while the brackets and screw mechanisms were printed from PLA. The printed main body was then copper-electroplated, creating a conductive layer 20 micrometers thick. The work therefore demonstrates a hybrid additive manufacturing workflow: polymer printing creates the structure, while metallization supplies the conductive waveguide surfaces.

The approach also illustrates a design consideration for additive manufacturing: geometry must account for the properties and limitations of the chosen process. For example, a conventional power splitter can use a thin metallic septum, but a thin printed polymer wall may be vulnerable to warping during electroplating. The design replaced the septum with a cylindrical stainless-steel pin, positioned using electromagnetic simulation.

Measured performance and practical considerations

Measurements showed input return loss better than 12.9 dB across the 15–17 GHz operating range without dielectric inserts. With the inserts at maximum depth, the worst-case return loss was 16.3 dB. The measured radiation patterns showed total beam-steering ranges of 54 degrees at 15 GHz and 52 degrees at 17 GHz, with steering from approximately −27 to +27 degrees at 15 GHz and −25 to +27 degrees at 17 GHz.

At broadside, measured antenna gain was 15.7 dBi at 15 GHz and 17.0 dBi at 17 GHz. The researchers reported close agreement between measured and simulated beam profiles and steering angles. Differences in gain between the measured prototype and idealized electromagnetic simulations were attributed to finite metallization conductivity, surface roughness, and small defects. These factors matter when evaluating printed RF hardware: simulation results based on ideal conductive walls do not capture every loss mechanism in a finished part.

For engineers and system integrators, the significance is not simply that an antenna can be printed. It is that additive manufacturing can be used to consolidate a multi-component microwave subsystem, while still delivering measured steering and return-loss performance. The prototype also makes clear that process selection, surface treatment, material behavior, and mechanical control of moving elements all contribute to system performance.

What this means for RF subsystem design

This Ku-band demonstrator provides a concrete example of additive manufacturing applied beyond an individual RF component. PolyJet formed the integrated waveguide structure, FDM supplied adjustable dielectric parts, and copper electroplating made the polymer body suitable for microwave operation. Together, these methods produced a four-element steerable array with a fully integrated feed network.

The practical takeaway is that 3D printing can support complex RF assemblies where reducing separate parts and interfaces is valuable, but it does not remove the need for careful electromagnetic design and manufacturing control. For teams assessing printed microwave hardware, the relevant questions include how the geometry will be metallized, how material and surface characteristics affect losses, and how reliably adjustable elements can be positioned. Addressing those details is central to turning an integrated design into a functioning subsystem.

Access Official Technical PDF

About The Author