A sound CEC1702 PCB layout starts with managing power and return paths, protecting sensitive signals, and planning interfaces around the device’s specific requirements. The 84-pin WFBGA integrates several functional blocks with different external connections, so placement and routing choices can affect clock accuracy, PLL jitter, ADC sampling and interface behavior. The following design priorities help engineers and system integrators turn those requirements into practical board-layout decisions.
CEC1702 PCB layout: start with power integrity
Place bypass capacitors as close as practical to the relevant supply pins, using short, wide connections. Each VCC pin should have a 0.1 µF capacitor nearby. Connecting capacitor pads to power and ground planes with two vias per pad can help reduce series inductance. If capacitors are placed on the board’s underside, use a short path to the device and ground plane.
The integrated core regulator has a separate critical requirement: a 1 µF low-ESR capacitor on the CAP pin. The capacitor’s ESR, including routing resistance, must be below 100 mΩ. Keep this connection close to the device and away from noise sources. Decoupling capacitors can carry substantial current, so keep sensitive traces—particularly the 32.768 kHz crystal connections—away from them. Where possible, maintain separation of at least five times the trace width.
Protect the low-frequency clock and PLL supply
Crystal oscillator placement
The external 32.768 kHz crystal supports the CEC1702 RTC function and can provide the internal 32 kHz clock domain. This low-power oscillator is designed for a parallel-resonant crystal; a standard inverter-style crystal layout should not be assumed. The design guidance recommends 10 pF load capacitors with a crystal rated for a 9 pF load. Keep the crystal and its connections away from switching and decoupling noise, and avoid adding external components beyond those required for the normal circuit.
Clock accuracy depends directly on the crystal’s frequency accuracy. The guidance recommends a ±20 ppm crystal for RTC accuracy requirements, with other sources of error considered separately. An external single-ended 32.768 kHz clock can instead be applied to XTAL2, with XTAL1 left floating, when the relevant clock configuration is selected. Confirm that the external source remains available in every power state where the embedded controller must operate.
PLL filtering and return paths
The PLL needs a suitably quiet analog supply to support reasonable long-term jitter. An RC or RLC filter may be used, but the series element must not cause an excessive DC voltage drop; the guidance calls for substantially less than 5% under worst-case conditions. Avoid a high-Q series resonance: a resistor, or a sufficiently resistive inductor, is preferred over a high-quality inductor used without series resistance.
Place the high-frequency capacitor close to the device, with short connections to the IC supply and ground pins. The supply path should run from the package pin through the high-frequency capacitor, then the low-frequency capacitor and series element, to board power. Keep the corresponding ground path close and parallel. For the described modern PLL arrangement, the external quiet-ground connection must not be tied to the board ground plane; follow the device-specific connection scheme rather than treating these pins as ordinary supply-plane connections. Component values shown in reference circuits are illustrative, so verify the current device documentation for the intended design.
Plan WFBGA escape and interface routing
The CEC1702 is available in an 84-pin WFBGA with a 0.65 mm ball pitch. Fine-pitch BGA routing is process-dependent: review the board fabricator’s capabilities and the latest land-pattern guidance before finalizing the footprint and escape strategy. The layout guide advises against conventional through-hole vias at pitches below 0.8 mm and identifies microvias as an option for denser routing. Avoiding through-hole vias can also support routing density and electrical performance.
SPI flash architecture should be selected deliberately. The shared interface can connect the CEC1702, host and flash on a common topology; the private interface provides a non-shared flash connection. Both approaches require electrical analysis of termination values and signal timing. In the shared topology, the specified route segments should be matched as described in the design guidance. For either implementation:
- Check signal integrity for each flash device and driver combination; termination values may need adjustment when components change.
- Keep SPI_CLK 20 mils from other signals above 1 GHz, and target 50 Ω trace impedance within ±15% at 50 MHz.
- Match SPI data I/O trace lengths to the clock within 0.100 inch.
- Use a weak chip-select pull-up tied to the same supply rail as the flash, with a value that meets its rise-time requirements.
- Confirm the selected flash meets the CEC1702 interface requirements and observe the specified firmware and host tri-state sequencing.
Account for ADC, external signals and configuration pins
ADC inputs can show sampling glitches in one-shot or long-report operation because the internal sampling node can discharge between samples. The layout guidance recommends an external input capacitor between 0.01 µF and 0.1 µF to help retain the sampled charge. For high sampling frequencies, select the input RC cutoff with the sampling rate in mind; the guide recommends setting it at one-twentieth of the ADC sampling frequency.
Signals routed to external connectors also deserve protection planning. SMBus lines, including connections to an external smart battery, may be exposed to electrical overstress and electrostatic discharge. The cited SMBus guidance recommends series protection resistance and an optional ESD suppressor; the application note also describes Schottky diode pairs as an alternative protection approach. Consider exposure for other connector signals as well, including GPIO-connected identification pins.
Check strap and power sequencing requirements against the device data sheet. GPIO171 is sampled at VTR power-up for TAP-controller selection, and the layout guidance states that it must be pulled low for normal operation. VBAT must be present whenever VTR is present. GPIO supply regions VTR1 and VTR2 may operate at either 1.8 V or 3.3 V, so confirm the intended voltage for each region and connected device. If VCI_IN pins are used as GPIO, firmware must select the GPIO function and disable the VCI input by clearing the specified buffer-enable and input-enable bits.
Make JTAG behavior intentional
CEC1702 supports four-wire JTAG and two-wire ARM SWD. Route debug signals with signal integrity in mind, particularly the clock: keep traces straight, minimize vias and layer changes, and provide an adjacent ground plane for outer-layer routing. A keyed connector helps prevent reverse insertion. Provide the necessary ground and target-voltage connections, and consider pull-ups to prevent JTAG inputs from floating when the cable is disconnected.
JTAG_RST# requires careful power-up handling. It must be held low during power-up for at least 5 ms so JTAG registers can initialize predictably. A jumper or an appropriately designed RC circuit can provide this interval; verify the timing against the actual VTR rise behavior. The pin should also be terminated in all functional states, whether the design enables JTAG in production or disables it while retaining a means of access for failure analysis.
Conclusion: validate the complete board implementation
Successful CEC1702 board design depends on applying device-specific layout rules across power, clocks, analog filtering, BGA escape, external interfaces and reset behavior. Keep critical components and paths close to their pins, preserve quiet supply and return routing, and assess SPI and JTAG signal integrity in the context of the actual devices and board stack-up. Before release, check the latest CEC1702 data sheet, reference schematic and package land-pattern information; the layout guide’s example values and recommendations are not a substitute for design-specific verification.