Access Official Technical PDF

Share Summary:LinkedInEmail

Semiconductor pressure transmitters convert process pressure into an electrical signal for monitoring gas supply equipment and facility systems. In semiconductor manufacturing, selecting a transmitter involves more than matching a pressure range: engineers must also consider cleanliness, wetted-material compatibility, connection design, and the conditions where the instrument will be installed.

The ZT11 is designed for semiconductor-industry gas applications. Its sensing element uses a semiconductor strain gauge with an evaporation-coated construction and an integrated electronic circuit. The unit is described as more compact and lightweight than a conventional pressure transmitter. EP and GP grades are standard, with UC grade available as an option.

Semiconductor pressure transmitters: design priorities

Gas-contact surfaces and assembly practices matter in equipment handling high-purity gases, semiconductor material gases, purge gases, or exhaust gases. The ZT11 uses a SUS316L pressure sensor welded directly to the fitting. This construction is intended to provide corrosion resistance, airtightness, long-term stability, and reliability. Co-Ni alloy is also available for the UC grade.

Material selection still requires application review. The gas-contact materials must be compatible with the process medium; the transmitter’s stated material options do not remove the need to confirm that compatibility for each gas and operating condition.

Cleanliness is addressed through assembly, adjustment, inspection, and packaging in a clean room, with attention paid to maintaining cleanliness. The product information lists EP and GP as standard grades and UC as an optional ultra-clean grade. For UC grade, double-melt material can be requested, and EP or UC grade is described as rising with double packing filled with nitrogen. Confirm the required grade and construction details with the supplier when specifying the instrument.

Choosing a grade and connection

Grade selection should reflect the gas service and the cleanliness requirements of the installation. The product information gives the following distinctions:

  • EP (Electro Polishing) and GP (General Purpose): Standard grade options, with SUS316L listed for the pressure sensor and fitting.
  • UC (Ultra Clean): An optional grade for applications requiring the specified ultra-clean provisions. Co-Ni alloy is available in this grade, and double-melt material may be requested.

The listed cleanliness criteria include helium leak rates of 5 × 10-12 Pa·m³/s or less and different surface-roughness values for gas-contact surfaces by grade. The product information also describes particle inspection with zero counts for particles of 0.1 μm or greater under its inspection standard. These are stated product criteria, not a substitute for checking the requirements of a particular process or facility.

Connections include options compatible with 1/4-inch VCR, 1/2-inch (3/8-inch) VCR, and 1/4-inch UJR. The internal volume is approximately 0.9 cm³ for the stated S-type, 1/4-inch UJR configuration; it varies with fitting shape. Connection choice can affect installation layout and the gas path, so confirm the exact fitting configuration during specification.

Pressure range, output, and installation details

Available pressure ranges include positive ranges from 0 to 0.3 MPa through 0 to 20 MPa, as well as compound ranges beginning at -0.1 MPa and extending to selected upper limits. The specified output is 4–20 mA DC on a two-wire system, with a 15–24 V DC supply for the standard version. Zero and span adjustment are made externally using trimmers on the top surface.

Accuracy options are ±0.25% of full scale or ±0.5% of full scale at 23°C. Linearity is listed as ±0.05% of full scale per °C for zero and span. These figures should be reviewed alongside the selected range, temperature conditions, and measurement requirements. The transmitter also has an IP67 dust-protected and waterproof construction in the specified connector-mated configuration; protection ratings depend on the connection condition stated for the product.

Electrical connection is through an M12, four-pin connector. A two-wire loop connects the supply and receiver according to the wiring information: brown is positive supply and blue is negative supply. The maximum load resistance depends on supply voltage, using the stated relationship R max. (Ω) = 50E − 500, where E is the supply voltage. Check loop requirements and wiring against the installation design before commissioning.

Non-incendive option for Zone 2

A non-incendive version is available with type of protection “n” and IECEx and ATEX certifications. The product information identifies it for Zone 2, Category 3G applications involving gas groups IIA, IIB, or IIC and temperature classes T4, T5, or T6, subject to the applicable certification and installation conditions. It is intended for use without a safety barrier in the stated Zone 2 setting.

The type-of-protection version has temperature-class-dependent operating limits: T4 is listed from -20°C to 80°C, T5 from 0°C to 50°C, and T6 from 0°C to 35°C. Do not assume that limits for the standard version apply to the non-incendive model. Check the marking, certification, temperature class, enclosure protection, and intended installation area when choosing the variant.

Practical selection checklist

Before specifying a transmitter for semiconductor gas equipment, engineers and integrators should verify:

  • The process pressure range and whether the application requires a positive or compound range.
  • Gas compatibility with all wetted parts and the required cleanliness grade.
  • The fitting type, size, and internal-volume configuration.
  • Loop supply voltage, load resistance, connector, and cable requirements.
  • Operating temperature and, where relevant, hazardous-area classification and certification.
  • Allowable maximum pressure and the limits on overpressure exposure.

The stated allowable maximum pressure is an upper limit for pressure that may be applied a couple of times for about 10 minutes, after which the pressure returns to the rated range. Effects of continuous overpressure are not guaranteed. This distinction is important when assessing upset conditions and pressure protection.

Conclusion

Choosing semiconductor pressure transmitters requires a coordinated review of measurement range, gas-contact materials, cleanliness grade, connections, electrical loop design, and installation environment. The ZT11 product information provides standard EP and GP grades, an optional UC grade, and a certified non-incendive version for specified Zone 2 applications. Matching those options to process and facility requirements—and confirming material compatibility and operating limits—helps ensure the instrument is appropriately specified for its role in semiconductor gas systems.

Access Official Technical PDF

About The Author